4101:2-15-01. Referenced standards

1501.1 General. This chapter lists the codes and standards that are referenced in various sections of this document. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and the title. The application of the referenced standards shall be as specified in Section 102.5 of the building code.

1501.2 Referenced codes: When indicated in the OMC, the following codes refer to provisions in the listed chapters of the Administrative Code:

Referenced code	Ohio Administrative Code chapters
Building Code	4101:1-1 to 4101:1-35
Fire Code	1301:7-1 to 1301:7-7
Ohio Boiler and Pressure Vessel Rules	4101:4-1 to 4101:4-10
Plumbing Code	4101:3-1 to 4101:3-15

1501.3 Referenced Standards.

ACCA Air Conditioning Contractors of America 2800 Shirlington Road, Suite 300 Arlington, VA 22206

Standard Referenced	Title
Manual D-2014 183-2007 (reaffirmed 2011)	Residential Duct Systems Peak Cooling and Heating Load Calculations in Buildings Except Low-rise Residential Buildings

AHRI Air-Conditioning, Heating and Refrigeration Institute

4100 North Fairfax Drive, Suite 200

Arlington, VA 22203

Standard Referenced	Title
700-2016	Purity Specifications for Fluorocarbon and
with Addendum 1	Other Refrigerants

AMCA Air Movement and Control Association International

30 West University Drive

Arlington Heights, IL 60004

Standard Referenced	Title
230-CD1	Laboratory Methods of Testing Air Circulating Fans for Rating and Certification
550-15	Test Method for High Velocity Wind Driven Rain Resistant Louvers

ANSI American National Standards Institute

11 West 42nd Street

New York, NY 10036

Standard Referenced	Title
Z 21.8 -1994 (R2012)	Installation of Domestic Gas Conversion Burners

ASHRAE American Society of Heating, Refrigerating and Air

-Conditioning Engineers

1791 Tullie Circle, NE

Atlanta, GA 30329

Standard Referenced	Title
Handbook-2013 15-2013 34-2013	ASHRAE Fundamentals Handbook Safety Standard for Refrigeration Systems Designation and Safety Classification of Refrigerants
62.1 -2016	Ventilation for Acceptable Indoor Air Quality
62.2 -2016	Ventilation and Acceptable Indoor Air Quality in Low-Rise Residential Buildings
170-2013	Ventilation of Health Care Facilities
180-2012	Standard Practice for Inspection and Maintenance of Commercial Building HVAC Systems

ASME American Society of Mechanical Engineers

Three Park Avenue

New York, NY 10016-5990

Standard Referenced	Title
B1.20.1-2013	Pipe Threads, General Purpose (Inch)
B 16.3 -2011	Malleable Iron Threaded Fittings, Classes 150 & 300
B 16.5 -2013	Pipe Flanges and Flanged Fittings NPS ½ through NPS 24
B 16.9 -2012	Factory Made Wrought Steel Buttwelding Fittings
B 16.11 -2011	Forged Fittings, Socket-welding and Threaded
B 16.15 -2013	Cast Bronze Threaded Fittings
B 16.18 -2012	Cast Copper Alloy Solder Joint Pressure Fittings
B 16.22 -2-13	Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
B 16.24 -2011	Cast Copper Alloy Pipe Flanges and Flanged Fittings: Class 150, 300, 400, 600, 900, 1500 and 2500
B 16.26 -2013	Cast Copper Alloy Fittings for Flared Copper Tubes
B 16.28 -1994	Wrought Steel Buttwelding Short Radius Elbows and Returns
B 16.51 -2013	Copper and Copper Alloy Press-Connect Pressure Fittings
B 31.5 -2016	Refrigeration Piping and Heat Transfer Components
B 31.9 -2014 BPVC- the edition referenced in rule 4101:4-3-01 of the Administrative Code CSD-1-the edition referenced in rule 4101:4-3-01 of the Administrative Code	Building Services Piping ASME Boiler & Pressure Vessel Code Controls and Safety Devices for Automatically Fired Boilers

ASSE American Society of Safety Engineers

1800 East Oakton Street

Des Plaines, IL 60018

Standard Referenced	Title
ANSI/ASSE Z 359.1 -2007	Safety Requirements for Personal Fall Arrest Systems, Subsystems and Components, Part of the Fall Protection Code

ASSE American Society of Sanitary Engineering

901 Canterbury, Suite A

Westlake, OH 44145

Standard Referenced	Title
1017-2010	Performance Requirements for Temperature Actuated Mixing Values for Hot Water Distribution Systems

ASTMInternational

100 Barr Harbor Drive

West Conshohocken, PA 19428

Standard Referenced	Title
A 53/A 53M-12	Specification for Pipe, Steel, Black and Hot-dipped, Zinc-coated Welded and Seamless
A 106/A106M-14	Specification for Seamless Carbon Steel Pipe for High-Temperature Service
A 126-14	Specification for Gray Iron Castings for Valves, Flanges and Pipe Fittings
A 234/A234M-15	Standard Specification for Piping Fittings of Wrought Carbon Steel And Alloy Steel For
A 254/A254-12	Moderate and High Temperature Service Specification for Copper Brazed Steel Tubing
A 395/A395M-14	Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures
A 420/A 420M-16	Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service
A 536-14	Standard Specification for Ductile Iron Castings
A 539-99	Specification for Electric-resistance-welded Coiled Steel Tubing for Gas and Fuel Oil Lines
B 32-14 B 42-15	Specification for Solder Metal Specification for Seamless Copper Pipe, Standard Sizes
B 43-15	Specification for Seamless Red Brass Pipe, Standard Sizes
B 68-11	Specification for Seamless Copper Tube, Bright Annealed
B75-11 B 88-14	Specification for Seamless Copper Tube Specification for Seamless Copper Water Tube
B 135-10	Specification for Seamless Brass Tube
B 251-10	Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube
B 280-16	Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service
B 302-12	Specification for Threadless Copper Pipe, Standard Sizes
B 813-16	Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube
C 315-07(2011)	Specification for Clay Flue Liners and Chimney Pots
C 411-11	Test Method for Hot-surface Performance of High-temperature Thermal Insulation
D 56-16	Test Method for Flash Point by Tag Closed Tester
D 93-16	Test Method for Flash Point of Pensky-Martens Closed Cup Tester
D 1527-99(2005)	Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80
D 1693-15	Test Method for Environmental Stress-Cracking of Ethylene Plastics
D 1785-15	Specification for Poly (Vinyl Chloride)(PVC) Plastic Pipe, Schedules 40, 80 and 120
D 2235-04(2011)	Specifications for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
D 2241-15	Specification for Poly (Vinyl Chloride)(PVC) Pressure-rated Pipe (SDR-Series)
D 2282-99(2005)	Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR)
D 2412-11	Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-plate Loading
D2464-15	Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
D 2466-15	Specification for Poly (Vinyl Chloride)(PVC) Plastic Pipe Fittings, Schedule 40
D 2467-15	Specification for Poly (Vinyl Chloride)(PVC) Plastic Pipe Fittings, Schedule 80
D 2564-12	Specification for Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems
D 2657-15	Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings.
D 2683-14	Specification for Socket-type Polyethylene Fittings for Outside Diameter-controlled Polyethylene Pipe and Tubing
D2737-12A	Standard Specification for Polyethylene (PE) Plastic Tubing
D 2846/D 2846M-14	Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot and Cold Water Distribution Systems
D 2996-15	Specification for Filament-wound Fiberglass (Glass Fiber Reinforced Thermosetting Resin) Pipe
D 3035-2015	Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
D 3261-15	Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
D 3278-1996(2011)	Test Methods for Flash Point of Liquids by Small Scale Closed-cup Apparatus
D 3309-96a(2002)	Specification for Polybutylene (PB) Plastic Hot and Cold Water Distribution Systems
E 84-16	Test Method for Surface Burning Characteristics of Building Materials
E 119-2016a	Test Method for Fire Tests of Building Construction and Materials
E 136-16	Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 Degrees C
E 814-2013a	Test Method for Fire Tests of Through-penetration Fire Stops
E 1509-12	Specification for Room Heaters, Pellet Fuel-burning Type
E 2231-15	Standard Practice For Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface
E 2336-16	Burning Characteristics Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems
F437-15	Specification for Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
F 438-15	Specification for Socket Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40
F 439-13	Specification for Socket Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
F 441/F 441M-15	Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80
F 442/F 442M-13	Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR)
F 493-14	Specification for Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings
F 714-13	Standard Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) based on Outside Diameter
F 876-2015a	Specification for Cross-linked Polyethylene (PEX) Tubing
F 877-2011A	Specification for Cross-linked Polyethylene (PEX) Plastic Hot and Cold Water Distribution Systems
F 1055-15	Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Cross-linked Polyethylene Pipe and Tubing
F 1281-11	Specification for Cross-linked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe
F 1282-10	Standard Specification for Polyethylene/Aluminum/ Polyethylene (PE-AL-PE) Composite Pressure Pipe
F 1476-07(2013)	Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications
F 1548-01(2012)	Standard Specification for the Performance of Fittings for Use with Gasketed Mechanical Couplings Used in Piping Applications
F 1807-15	Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR 9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polethylene of Raised Temperature (PE-RT) Tubing
F 1924-12	Standard Specification for Plastic Mechanical Fittings for Use on Outside
	Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
F1960-15	Specification for Cold-Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing
F 1974-09(2015)	Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Composite Pressure Pipe
F2080-15a	Specification for Cold-Expansion Fittings with Metal Compression-Sleeves for Cross-linked Polyethylene (PEX) Pipe
F2098-15	Standard Specification for Stainless Steel Clamps for SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal and Plastic Insert Fittings
F 2159-14	Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR 9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
F 2389-15	Specification for Pressure-rated Polypropylene Piping Systems
F2434-14	Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/ Cross-linked Polyethylene (PEX-AL-PEX) Tubing
F 2623-14	Standard Specification for Polyethylene of Raised Temperature (PE-RT) SDR 9 Tubing1
F 2735-09(2016)	Standard Specification for Plastic Insert Fittings for SDR 9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing
F 2769-14	Polyethylene of Raised Temperature (PERT) Plastic Hot- and Cold-water Tubing and Distribution Systems
F 2806-15	Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (Metric SDR-PR)

AWS American Welding Society

8669 NW 36 Street, #130

Doral, FL 33166

Standard Referenced	Title
A 5.8 M/A 5.8 -2011	Specifications for Filler Metals for Brazing and Braze Welding

AWWA American Water Work Association

6666 West Quincy Avenue

Denver, CO 80235

Standard Referenced	Title
C901-08	Polyethylene (PE) Pressure Pipe and Tubing, 1/ in. (13mm) through 3 in. (76mm) for Water Service
C110/A 21.10 -12	Standard for Ductile Iron & Gray Iron Fittings
C115/A 21.15 -11	Standard for Flanged Ductile-Iron Pipe with Ductile Iron or Grey-Iron Threaded Flanges
C151/A 21.51 -09	Standard for Ductile-Iron Pipe, Centrifugally Cast for Water
C153/A 21.53 -11	Standard for Ductile-Iron Compact Fittings for Water Service

CSA CSA Group

8501 East Pleasant Valley Road

Cleveland, OH 44131-5516

Standard Referenced	Title
B 137.2 -13	Polyvinylchloride (PVC) Injection-moulded Gasketed Fittings for Pressure Applications
B 137.3 -13	Rigid Poly (Vinyl Chloride) (PVC) Pipe for Pressure Applications
B 137.6 -13	Chlorinated Polyvinylchloride (CPVC) Pipe, Tubing and Fittings for Hot- and Cold-water Distribution Systems
B 137.9 -13	Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure-Pipe Systems
B 137.10 -13	Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Composite Pressure-Pipe Systems
CSA C448 Series-13	Design and Installation of Earth Energy Systems-First Edition; Update 2: October 2009; CAN/CSA 2002 Consolidated Reprint 10/2009
CSA B 137.1 -13	Polyethylene (PE) Pipe, Tubing and Fittings for Cold Water Pressure Services.
CSA B 137.5 -13	Cross-linked Polyethylene (PEX) Tubing Systems for Pressure Applications
CSA B 137.11 -13	Polypropylene (PP-R) Pipe and Fittings for Pressure Applications
ANSI CSA America FC1-2014	Stationary Fuel Cell Power Systems

DOL Department of Labor

Occupational Safety and Health Administration c/o Superintendent of Documents

US Government Printing Office

Washington, DC 20402-9325

Standard Referenced	Title
29 CFR Part 1910.1000 (2016)	Air Contaminants
29 CFR Part 1910.1025 (2016)	Toxic and Hazardous Substances

FS Federal Specifications*

General Services Administration 7th & D Streets

Specification Section, Room 6039 Washington, DC 20407

Standard Referenced	Title
WW-P-325B (1976)	Pipe, Bends, Traps, Caps and Plugs; Lead (for Industrial Pressure and Soil and Waste Applications) *Standards are available from the Supt. of Documents, U.S. Government Printing Office, Washington, DC 20402-9325

ICC International Code Council, Inc.

500 New Jersey Ave, NW

6th Floor

Washington, DC 20001

Standard Referenced	Title
IECC-12 IFGC-15	International Energy Conservation Code® International Fuel Gas Code®

IIAR International Institute of Ammonia Refrigeration

1110 North Glebe Road

Arlington, VA 22201

Standard Referenced	Title
2-2014	Addendum A to Equipment, Design, and Installation of Ammonia Mechanical Refrigerating Systems

MSS Manufacturers Standardization Society of the Valve & Fittings Industry, Inc.

127 Park Street, N.E.

Vienna, VA 22180

Standard Referenced	Title
SP 58-2009	Pipe Hangers and Supports-Materials Design and Manufacture, Selection, Application and Installation

NAIMA North American Insulation Manufacturers Association

44 Canal Center Plaza, Suite 310

Alexandria, VA 22314

Standard Referenced	Title
AH116-09	Fibrous Glass Duct Construction Standards

NBBI National Board of Boiler and Pressure Vessel Inspectors

1055 Crupper Avenue

Columbus, OH 43229-1183

Standard Referenced	Title
NBIC- the edition referenced in rule 4101:4-3-01 of the Administrative Code	National Board Inspection Code, Part 3

NFPA National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

Standard Referenced	Title
30-15 30A-15	Flammable and Combustible Liquids Code Code for Motor Fuel-dispensing Facilities and Repair Garages
31-16	Standard for the Installation of Oil-burning Equipment
37-15	Standard for the Installation and Use of Stationary Combustion Engines and Gas Turbines
58-17	Liquefied Petroleum Gas Code
69-14	Standard on Explosion Prevention Systems
70-17	National Electrical Code
72-16	National Fire Alarm and Signaling Code
75-09	Protection of Information Technology Equipment
82-14	Standard on Incinerators and Waste and Linen Handling Systems and Equipment
85-the edition referenced in rule 4101:4-3-01 of the Administrative Code	Boiler and Combustion Systems Hazards Code
91-15	Standard for Exhaust Systems for Air Conveying of Vapors, Gases, Mists, and Noncombustible Particulate Solids
92-15	Standard for Smoke Control Systems
96-14	Standard for Ventilation Control and Fire Protection of Commercial Cooking Operations
211-16	Standard for Chimneys, Fireplaces, Vents and Solid Fuel-burning Appliances
262-15	Standard Method of Test for Flame Travel and Smoke of Wires and Cables for Use in Air-handling Spaces
286-15	Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth 602.2.1.6.2
704-17	Standard System for Identification of the Hazards of Materials for Emergency Response
853-15	Standard on Installation of Stationary Fuel Power Plants

NSF NSF International

789 Dixboro Road, P. O. Box 130140

Ann Arbor, MI 48113-0140

Standard Referenced	Title
NSF 358-1-2014	Polyethylene Pipe and Fittings for Water Based Ground Source "Geothermal" Heat Pump Systems

SMACNA Sheet Metal & Air-Conditioning Contractors National Assoc., Inc.

4201 Lafayette Center Drive

Chantilly, VA 20151-1209

Standard Referenced	Title
SMACNA/ANSI-2015	HVAC Duct Construction Standards-Metal and Flexible 4th Edition (ANSI)
SMACNA-10	Fibrous Glass Duct Construction Standards

UL Underwriters Laboratories LLC

333 Pfingsten Road

Northbrook, IL 60062-2096

Standard Referenced	Title
17-2008	Vent or Chimney Connector Dampers for Oil-fired Appliances- with revisions Through January 2010 803.6
103-2010	Factory-built Chimneys, Residential Type and Building Heating Appliance- with revisions through July 2012
127-2011	Factory-built Fireplaces
174-04	Household Electric Storage Tank Water Heaters-with revisions through September 2012
180-2012	Liquid-level Indicating Gauges for Oil Burner Fuels and Other Combustible Liquids
181-13	Factory-made Air Ducts and Air Connectors
181A-2013	Closure Systems for Use with Rigid Air Ducts and Air Connectors
181B-2013	Closure Systems for Use with Flexible Air Ducts and Air Connectors
197-10	Commercial Electric Cooking Appliances- with revisions through June 2011
207-2009	Refrigerant-containing Components and Accessories, Nonelectrical
263-2011	Standard for Fire Test of Building Construction and Materials
268-2016	Smoke Detectors for Fire Alarm Systems
268A-2008	Smoke Detectors for Duct Application-with revisions through September 2009
343-2008	Pumps for Oil-Burning Appliances-with revisions through June 2013
378-06	Draft Equipment-with revisions through January 2010
391-2010	Solid-fuel and Combination-fuel Central and Supplementary Furnaces-with revisions through March 2010
412-2011	Refrigeration Unit Coolers-with revisions through August 2012
471-2010	Commercial Refrigerators and Freezers- with revisions through December 2012
499-14	Electric Heating Appliances
508-99	Industrial Control Equipment-with revisions through March 2013
536-14	Flexible Metallic Hose
555-06	Fire Dampers-with revisions through May 2012
555C-14	Ceiling Dampers
555S-14	Smoke Dampers
586-2009	High-Efficiency, Particulate, Air Filter Units
641-2010	Type L Low-temperature Venting Systems- with revisions through May 2013
705-2004	Standard for Power Ventilators-with revisions through March 2012
710-2012	Exhaust Hoods for Commercial Cooking Equipment
710B-2011	Recirculating Systems
723-2008	Standard for Test for Surface Burning Characteristics of Building Materials
726-95	Oil-fired Boiler Assemblies-with revisions through April 2011
727-06	Oil-fired Central Furnace-with revisions through April 2010
729-03	Oil-fired Floor Furnaces-with revisions through August 2012
730-03	Oil-fired Wall Furnaces-with revisions through August 2012
731-95	Oil-fired Unit Heaters-with revisions through August 2012
732-95	Oil-fired Storage Tank Water Heaters-with revisions through April 2010
737-2011	Fireplace Stoves
762-2013	Outline of Investigation for Power Ventilators for Restaurant Exhaust Appliances
791-06	Residential Incinerators-with revisions through April 2010
834-04	Heating, Water Supply and Power Boilers Electric-with revisions through January 2013
842-15	Valves for Flammable Fluids
858-14	Household Electric Ranges
867-2011	Electrostatic Air Cleaners-with revisions through February 2013
875-09	Electric Dry Bath Heater-with revisions through November 2011
896-93	Oil-burning Stoves-with revisions through August 2012
900-15	Air Filter Units
907-16	Fireplace Accessories
923-2013	Microwave Cooking Appliances
959-2010	Medium Heat Appliance Factory-built Chimneys
1046-2010	Grease Filters for Exhaust Ducts-with revisions through January 2012
1240-2012	Electric Commercial Clothes-Drying Equipment-with revisions through October 2012
1261-01	Electric Water Heaters for Pools and Tubs- with revisions through July 2012
1453-16	Electric Booster and Commercial Storage Tank Water Heaters
1479-15	Fire Tests of Through-penetration Firestops
1482-2011	Solid-fuel Type Room Heaters
1618-15	Wall Protectors, Floor Protectors and Hearth Extensions
1777-2015	Chimney Liners
1812-2013	Standard for Ducted Heat Recovery Ventilators
1815-2012	Standard for Nonducted Heat Recovery
1820-04	Fire Test of Pneumatic Tubing for Flame and Smoke Characteristics-with revisions through May 2013
1887-04	Fire Tests of Plastic Sprinkler Pipe for Visible Flame and Smoke Characteristics- with revisions through May 2013
1978-2010	Grease Ducts
1995-2015	Heating and Cooling Equipment
1996-2009	Electric Duct Heaters-with revisions through November 2011
2024-2014	Standard for Safety Optical-Fiber and Communications Cable Raceway- with revisions through April 2011
2043-2013	Fire Test for Heat and Visible Smoke Release for Discrete Products and their Accessories Installed in Air-handling Spaces
2085-10	Protected Above-Ground Tanks for Flammable and Combustible Liquids
2158-15	Electric Clothes Dryers
2158A-2013	Outline of Investigation for Clothes Dryer Transition Duct
2162-14	Outline of Investigation for Commercial Wood-fired Baking Ovens-Refractory Type
2200-2012	Stationery Engine Generator Assemblies- with revisions through June 2013
2221-2010	Tests of Fire Resistive Grease Duct Enclosure Assemblies
2518-16	Air Dispersion System Materials
2523-09	Solid Fuel-fired Hydronic Heating Appliances-with revisions through February 2013

Replaces: 4101:2-15-01

Effective: 11/1/2017
Five Year Review (FYR) Dates: 11/01/2022
Promulgated Under: 119.03
Statutory Authority: 3781.10(A)
Rule Amplifies: 3781.10 , 3781.11, 3791.04
Prior Effective Dates: 7/1/82, 3/1/85, 3/1/86, 1/1/89, 9/1/92, 7/1/95, 2/1/96, 3/1/98, 7/1/98, 1/1/02, 1/1/04, 3/1/05, 9/6/05, 3/1/06, 7/1/07, 1/1/08, 3/31/08(Emer.), 6/24/08, 1/1/09, 11/1/11, 3/1/13, 1/1/15, 1/1/16