4101:1-35-01 Referenced standards.
General. This chapter lists the standards that are referenced in various sections of the building code. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and title. The application of the referenced standards shall be as specified in Section 102.5.
Referenced codes. When indicated in this code, the following codes refer to provisions in the listed chapters of the administrative code:
Referenced Code
Ohio Administrative Code Chapters
Building Code
4101:1-1 to 4101:1-35
Energy Code
4101:1-13
Fire Code
1301:7-1 to 1301:7-7
Mechanical Code
4101:2-1 to 4101:2-15
Ohio Boiler and Pressure Vessel Rules
4101:4-1 to 4101:4-10
Ohio Elevator Code
4101:5-1 to 4101:5-3
Residential Code of Ohio for One, Two and
4101:8-1 to 4101:8-44
Three Family Dwellings Plumbing Code
4101:3-1 to 4101:3-13
Americans with Disabilities Act accessibility guidelines. When reference is made to ADAAG in this code, it shall mean the "ADA Standards for Accessible Design" also known as "ADA Accessibility Guidelines for Buildings and Facilities", "28 CFR Part 36 Appendix A" Code of Federal Regulations as reprinted and the version available on the U.S. department of justice's website at http://www.usdoj.gov/crt/ada/stdspdf.htm.
Building Code Referenced Standards.
Aluminum Association
1525 Wilson Boulevard, Suite 600 Arlington, VA 22209
AA
Standard reference
number Title
ADM1-10 Aluminum Design Manual: Part 1-A Specification for Aluminum Structures, Allowable Stress Design; and Part 1- B-Aluminum Structures, Load and Resistance Factor Design
ASM 35-00 Aluminum Sheet Metal Work in Building Construction (Fourth Edition)
American Architectural Manufacturers Association 1827 Waldon Office
Square, Suite 550 Schaumburg, IL 60173
AAMA
Standard reference
number Title
1402-09 Standard Specifications for Aluminum Siding, Soffit and Fascia
AAMA/WDMA/CSA
101/I.S.2/A440-08 North American Fenestration
Standard/Specifications for Windows, Doors and Skylights
American Concrete Institute 38800 Country Club Dive Farmington Hills, MI 48331
ACI
Standard reference
number Title
216.1-07 Standard Method for Determining Fire Resistance of Concrete and Masonry Construction Assemblies
318-08 Building Code Requirements for Structural Concrete 530-08 Building Code Requirements for Masonry Structures 530.1-08 Specifications for Masonry Structures
American Forest & Paper Association 1111 19th St, NW Suite 800 Washington, DC 20036
AF&PA
Standard reference
number Title
WCD No. 4-03 Wood Construction Data-Plank and Beam Framing for Residential
NDS-05 National Design Specification (NDS) for Wood Construction with 2005 Supplement
AF&PA-93 Span Tables for Joists and Rafters ANSI/AF&PA PWF-07 Permanent Wood Foundation Design
Specification
ANSI/AF&PA SDPWS-08 Special Design Provisions for Wind and Seismic
American Institute of Steel Construction One East Wacker Drive, Suite 3100 Chicago, IL 60601-2001
AISC
Standard reference
number Title
341-05 Seismic Provisions for Structural Steel Buildings, including Supplement No. 1 dated 2005
360-05 Specification for Structural Steel Buildings
American Iron and Steel Institute 1140 Connecticut Avenue
Suite 705
Washington, DC 20036
AISI
Standard reference
number Title
S100-07 North American Specification for the Design of Cold- formed Steel Structural Members
S200-08 North American Standard for Cold-formed Steel Framing-General
S210-08 North American Standard for Cold-formed Steel Framing-Floor and Roof System Design
S211-08 North American Standard for Cold-formed Steel Framing-Wall Stud
S212-08 North American Standard for Cold-formed Steel Framing-Header Design
S213-08 North American Standard for Cold-formed Steel Framing-Lateral Design
S214-08 North American Standard for Cold-formed Steel Framing-Truss Design, with Supplement 2, dated 2008
American Institute of Timber Construction Suite 140
7012 S. Revere Parkway Englewood, CO 80112
AITC
Standard reference
number Title
AITC Technical
Note 7-96 Calculation of Fire Resistance of Glued Laminated Timbers
AITC 104-03 Typical Construction Details
AITC 110-01 Standard Appearance Grades for Structural Glued
Laminated
AITC 113-01 Standard for Dimensions of Structural Glued
Laminated Timber
AITC 117-04 Standard Specifications for Structural Glued
Laminated Timber of Softwood Species
AITC 119-96 Standard Specifications for Structural Glued
Laminated Timber of Hardwood
AITC200-09 Manufacturing Quality Control Systems Manual for
Structural Glued Laminated Timber ANSI/AITCA 190.1-07 Structural Glued Laminated Timber
Automotive Lift Institute P.O. Box 85
Courtland, NY 13045
ALI
Standard reference
number Title
ALI ALCTV-2007 Standard for Automobile Lifts-Safety
Requirements for Construction, Testing and Validation (ANSI)
American National Standards Institute 25 West 43rd Street, Fourth Floor New York, NY 10036
ANSI
Standard reference
number Title
A13.1-07 Scheme for the Identification of Piping Systems A108.1A-09 Installation of Ceramic Tile in the Wet-set Method, with
Portland Cement
A108.1B-09 Installation of Ceramic Tile, quarry Tile on a Cured Portland Cement Mortar Setting Bed with Dry-set orLatex-
A108.4-09 Installation of Ceramic Tile with Organic Adhesives or Water-cleanable Tile-setting Epoxy Adhesive
A108.5-09 Installation of Ceramic Tile with Dry-set Portland Cement Mortar or Latex-portland Cement Mortar
A108.6-09 Installation of Ceramic Tile with Chemical-resistant,Water Cleanable Tile-setting and -grouting Epoxy
A108.8-09 Installation of Ceramic Tile with Chemical-resistant Furan Resin Mortar and Grout
A108.9-09 Installation of Ceramic Tile with Modified Epoxy Emulsion Mortar/Grout
A108.10-09 Installation of Grout in Tilework
A118.1-10.1 American National Standard Specifications for Dry-set Portland Cement
A118.3-10.1 American National Standard Specifications for Chemical- resistant, Water-cleanable Tile-setting and -grouting Epoxy and Water Cleanable Tile-setting Epoxy
A118.4-10.1 American National Standard Specifications for Latex- portland Cement
A118.5-10.1 American National Standard Specifications for Chemical Resistant Furan Mortar and Grouts for Tile
A118.8-10.1 American National Standard Specifications for Modified Epoxy Emulsion Mortar/Grout
A136.1-10.1 American National Standard Specifications for Organic Adhesives for Installation of Ceramic
137.1-08 American National Standard Specifications for Ceramic Tile
A208.1-09 Particleboard
Z 97.1-09 Safety Glazing Materials Used in Buildings-Safety Performance Specifications and Methods of Test
APA - Engineered Wood Association 7011 South 19th
Tacoma, WA 98466
APA
Standard reference
number Title
APA PDS-08 Panel Design Specification APA PDS
Supplement 1-90 Design and Fabrication of Plywood Curved Panels (revised 1995)
APA PDS
Supplement 2-92 Design and Fabrication of Plywood-lumber Beams (revised 1998
APA PDS
Supplement 3-96 Design and Fabrication of Plywood Stressed-skin Panels (revised 1996
APA PDS
Supplement 4-93 Design and Fabrication of Plywood Sandwich Panels (revised 1993)
APA PDS
Supplement 5-95 Design and Fabrication of All-plywood Beams (revised 1995
EWS R540-07 Builders Tips: Proper Storage and Handling of Glulam Beams
EWS S475-07 Glued Laminated Beam Design Tables
EWS S560-10 Field Notching and Drilling of Glued Laminated Timber Beams
EWS T300-07 Glulam Connection EWS X440-08 Product Guide- Glulam
EWS X450-01 Glulam in Residential Construction-Western Edition
The Association of Pool & Spa Professionals 2111 Eisenhower Avenue
Alexandria, VA 22314
APSP
Standard reference
number Title
ANSI/APSP 7-06 Standard for Suction Entrapment Avoidance in Swimming Pools, Wading Pools, Spas, Hot Tubs and Catch Basins
American Society of Agricultural and Biological Engineers 2950 Niles Road
St. Joseph, MI 49085
ASABE
Standard reference
number Title
EP 484.2 -98 Diaphragm Design of Metal-clad, Post-frame Rectangular Buildings
EP 486.1 -99 Shallow-post Foundation Design
EP 559 -03 Design Requirements and Bending Properties for Mechanically Laminated Columns
American Society of Civil Engineers Structural Engineering Institute 1801 Alexander Bell Drive
Reston, VA 20191-4400
ASCE/SEI
Standard reference
number Title
3-91 Structural Design of Composite Slabs 5-08 Building Code Requirements for Masonry 6-08 Specification for Masonry Structures
7-05 Minimum Design Loads for Buildings and Other Structures including Supplements No. 1 and 2, excluding Chapter 14 and Appendix 11A
8-02 Standard Specification for the Design of Cold-formed Stainless Steel Structural Members
19-10 Structural Applications of Steel Cables for Buildings 24-05 Flood Resistant Design and Construction
29-05 Standard Calculation Methods for Structural Fire Protection 32-01 Design and Construction of Frost Protected Shallow Foundations
American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. 1791 Tullie Circle, NE
Atlanta, GA 30329-2305
ASHRAE
Standard Reference
Number Title
ASHRAE 90.1-2007 Energy Standard for Buildings Except Low-Rise Buildings
American Society of Mechanical Engineers Three Park Avenue
New York, NY 10016-5990
ASME
Standard reference
number Title
A17.1/CSA B44-2004 Safety Code for Elevators and Escalators A18.1-2003 Safety Standard for Platform Lifts and Stairway
Chairlifts
A90.1-03 Safety Standard for Belt Manlifts B16.18-2001
(Reaffirmed 2005) Cast Copper Alloy Solder Joint Pressure Fittings B16.22-2001
(Reaffirmed 2005) Wrought Copper and Copper Alloy Solder Joint
Pressure Fittings
B20.1-2009 Safety Standard for Conveyors and Related
Equipment B31.3-2008 Process Piping
ASTM International 100 Barr Harbor Drive
West Conshohocken, PA 19428-2959
ASTM
Standard reference
number Title
A 36/A 36M-08 Specification for Carbon Structural Steel
A 153/A 153M-09 Specification for Zinc Coating (Hot-dip) on Iron
and Steel Hardware
A 240/A 240M-10a Standard Specification for Chromium and
Chromium-nickel Stainless Steel Plate,
Sheet and Strip for Pressure Vessels and for
General Applications
A 252-10 Specification for Welded and Seamless Steel Pipe Piles
A 283/A 283M-03(2007) Specification for Low and Intermediate Tensile
Strength Carbon Steel Plates
A 307-07b Specification for Carbon Steel Bolts and Studs, 60,000 psi Tensile Strength
A 416/A 416M-10 Specification for Steel Strand, Uncoated Seven-wire for Prestressed Concrete
A 463/A 463M-09a Standard Specification for Steel Sheet, Aluminum-
coated, by the Hot-dip Process
A 572/A 572M-07 Specification for High-strength Low-alloy
Columbium-vanadium Structural Steel
A 588/A 588M-10 Specification for High-strength Low-alloy
Structural Steel with 50 ksi (345 MPa)
Minimum Yield Point to 4 inches (100 mm) Thick A 615/A 615M-09b Specification for Deformed and Plain Billet-steel
Bars for Concrete Reinforcement
A 653/A 653M-09a Specification for Steel Sheet, Zinc-coated
Galvanized or Zinc-iron Alloy-coated
Galvannealed by the Hot-dip Process
A 690/A 690M-07 Standard Specification for High-strength Low-alloy
Nickel, Copper, Phosphorus Steel H-piles and
Sheet Piling with Atmospheric Corrosion
Resistance for Use in Marine Environments
A 706/A 706M-09b Specification for Low-alloy Steel Deformed and
Plain Bars for
Concrete Reinforcement
A 722/A 722M-07 Specification for Uncoated High-strength Steel Bar
for Prestressing
A 755/A 755M-03(2008) Specification for Steel Sheet, Metallic-coated by the
Hot-dip Process and Prepainted by the
Coil-coating Process for Exterior Exposed Building
Products
A 792/A 792M-09a Specification for Steel Sheet, 55% Aluminum-zinc
Alloy-coated by the Hot-dip Process
A 875/A 875M-09a Standard Specification for Steel Sheet Zinc-5
percent, Aluminum Alloy-coated by the Hot-dip Process
A 913/A 913M-07 Specification for High-strength Low-alloy Steel
Shapes of Structural Quality, Produced by Quenching and Self-tempering Process (QST)
A 924/A 924M-10 Standard Specification for General Requirements
for Steel Sheet, Metallic-coated by the Hot-dip Process
A 992/A 992M-06a Standard Specification for Structural Shapes
B 42-10 Specification for Seamless Copper Pipe, Standard
B 43-09 Specification for Seamless Red Brass Pipe, Standard Sizes
B 68-02 Specification for Seamless Copper Tube, Bright Annealed (Metric
B 88-09 Specification for Seamless Copper Water Tube
B 101-07 Specification for Lead-coated Copper Sheet and Strip for Building Construction
B 209-07 Specification for Aluminum and Aluminum Alloy Steel and Plate
B 251-10 Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube
B 280-08 Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service
B 370-09 Specification for Cold-rolled Copper Sheet and Strip for Building Construction
B 695-04(2009) Standard Specification for Coatings of Zinc
Mechanically Deposited on Iron and Steel
C 5-10 Specification for Quicklime for Structural C 22/C 22M-00 (2005)e01 Specification for Gypsum
C 27-98 (2008) Specification for Standard Classification of Fireclay
and High-alumina Refractory Brick C 28/C 28M-10 Specification for Gypsum
C 31/C 31M-10 Practice for Making and Curing Concrete Test Specimens in the Field
C 33-08 Specification for Concrete Aggregates
C 34-10 Specification for Structural Clay Load-bearing Wall Tile
C 35-01(2009) Specification for Inorganic Aggregates for Use in
Gypsum Plaster
C 36/C 36M-03 Specification for Gypsum Wallboard C 37/C 37M-01 Specification for Gypsum Lath
C 55-09 Specification for Concrete Building Brick
C 56-10 Specification for Structural ClayNonloadBearing Tile
C 59/C 59M-00 (2006) Specification for Gypsum Casting and Molding
Plaster
C 61/C 61M-00 (2006) Specification for Gypsum Keene's
C 62-10 Specification for Building Brick (Solid Masonry Units Made from Clay or Shale
C 67-09 Test Methods of Sampling and Testing Brick and Structural Clay
C 73-05 Specification for Calcium Silicate Face Brick (Sand-lime Brick)
C 79-04a Specification for Treated Core and Nontreated Core Gypsum Sheathing Board
C 90-09 Specification for Loadbearing Concrete Masonry Units
C 91-05 Specification for Masonry Cement C 94/C 94M-10 Specification for Ready-mixed
C 126-10 Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick and Solid Masonry Units
C 140-10 Test Method Sampling and Testing Concrete Masonry Units and Related Units
C 150-09 Specification for Portland Cement
C 172-10 Practice for Sampling Freshly Mixed
C 199-84 (2005) Test Method for Pier Test for Refractory Mortars C 206-03 (2009) Specification for Finishing Hydrated Lime
C 208-08a Specification for Cellulosic Fiber Insulating Board
C 212-10 Specification for Structural Clay Facing Tile
C 216-10 Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale
C 270-10 Specification for Mortar for Unit Masonry
C 315-07 Specification for Clay Flue Liners and Chimney Pots
C 317/C 317M-00 (2005) Specification for Gypsum Concrete
C 330-09 Specification for Lightweight Aggregates for Structural Concrete
C 331-05 Specification for Lightweight Aggregates for Concrete Masonry Units
C 406-10 Specification for Roofing Slate
C 442/C 442M-04 Specification for Gypsum Backing Board and
Coreboard and Gypsum Shaftliner Board
C 472-99 (2009) Specification for Standard Test Methods for
Physical Testing of Gypsum, Gypsum Plasters and Gypsum Concrete
C 473-10 Test Method for Physical Testing of Gypsum Panel Products
C 474-05 Test Methods for Joint Treatment Materials for Gypsum Board Construction
C 475-02 (2007) Specification for Joint Compound and Joint Tape
for Finishing Gypsum Wallboard
C 503-10 Specification for Marble Dimension Stone (Exterior C 514-04 (2009)e1 Specification for Nails for the Application of
Gypsum
C 516-08 Specifications for Vermiculite Loose Fill Thermal
C 547-07e1 Specification for Mineral Fiber Pipe Insulation
C 549-06 Specification forPerliteLoose Fill
C 552-07 Standard Specification for Cellular Glass Thermal Insulation
C 557-03(2009)e01 Specification for Adhesives for Fastening Gypsum
Wallboard to Wood Framing
C 568-10 Specification for Limestone Dimension Stone
C 578-10 Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation
C 587-04 (2009) Specification for Gypsum Veneer Plaster
C 588/C 588M-01 Specification for Gypsum Base for Veneer Plasters C 595-10 Specification for Blended Hydraulic Cements
C 615-10 Specification for Granite Dimension
C 616-10 Specification for Quartz Dimension Stone
C 629-10 Specification for Slate Dimension
C 630/C 630M-03 Specification for Water-resistant Gypsum Backing
Board
C 631-09 Specification for Bonding Compounds for Interior Gypsum Plastering
C 635/C 635M-07 Specification for the Manufacture, Performance and
Testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel
C 636/C 636M-08 Practice for Installation of Metal Ceiling
Suspension Systems for Acoustical Tile and Lay-in Panels
C 645-09a Specification for Nonstructural Steel Framing Members
C 652-10 Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale
C 728-05 (2010) Standard Specification forPerliteThermal Insulation
Board
C 744-10 Specification for Prefaced Concrete and Calcium Silicate Masonry
C 754-09a Specification for Installation of Steel Framing Members to Receive Screw-attached Gypsum Panel Products
C 836/C 836M-10 Specification for High-solids Content, Cold Liquid-
applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course
C 840-08 Specification for Application and Finishing of Gypsum Board
C 841-03 (2008)e1 Specification for Installation of Interior Lathing and
Furring
C 842-05 Specification for Application of Interior Gypsum Plaster
C 843-99 (2006) Specification for Application of Gypsum Veneer
Plaster
C 844-10 Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster
C 847-10a Specification for Metal Lath
C 887-05 (2010) Specification for Packaged, Dry Combined
Materials for Surface Bonding Mortar
C 897-05 (2009) Specification for Aggregate for Job-mixed Portland Cement-based Plaster
C 920-10 Standard for Specification forElastomericJoint Sealants
C 926-06 Specification for Application of Portland Cement- based Plaster
C 931/C 931M-04 Specification for Exterior Gypsum Soffit Board
C 932-06 Specification for Surface-applied Bonding Compounds Agents for Exterior Plastering
C 933-09 Specification for Welded Wire Lath
C 946-10 Specification for Practice for Construction of Dry- stacked, Surface-bonded Walls
C 954-10 Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 inch (0.84 mm) to 0.112 inch (2.84 mm) in Thickness
C 955-09a Standard Specification for Load-bearing Transverse and Axial Steel Studs, Runners Tracks, and Bracing or Bridging, for Screw Application of Gypsum Panel Products and Metal Plaster Bases
C 956-04 (2010) Specification for Installation of Cast-in-place
Reinforced Gypsum
C 957-10 Specification for High-solids Content, Cold Liquid- applied Elastomeric Waterproofing Membrane with Integral Wearing Surface
C 960-04 Specification forPredecoratedGypsum Board
C 1002-07 Specification for Steel Self-piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs
C 1007-08a Specification for Installation of Load Bearing
(Transverse and Axial) Steel Studs and Related Accessories
C 1019-09 Test Method of Sampling and Testing Grout
C 1029-10 Specification for Spray-applied Rigid Cellular Polyurethane Thermal Insulation
C 1032-06 Specification for Woven Wire Plaster Base
C 1047-10a Specification for Accessories for Gypsum
Wallboard and Gypsum Veneer
C 1063-08 Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement- based Plaster
C 1088-10 Specification for Thin Veneer Brick Units Made from Clay or Shale
C 1167-03 (2009) Specification for Clay Roof Tiles
C 1177/C 1177M-08 Specification for Glass Mat Gypsum Substrate for
Use as Sheathing
C 1178/C 1178M-08 Specification for Coated Glass Mat Water-resistant Gypsum Backing Panel
C 1186-08 Specification for Flat-Fiber Cement Sheets
C 1261-10 Specification for Firebox Brick for Residential Fireplaces
C 1278/C 1278M-07a Specification for Fiber-reinforced Gypsum Panels C 1280-09 Specification for Application of Gypsum Sheathing
C 1283-07a Practice for Installing Clay Flue Lining.
C 1288-99 (2010) Standard Specification for Discrete Nonasbestos
Fiber-cement Interior Substrate Sheets
C 1289-10 Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board
C 1314-10 Test Method for Compressive Strength of Masonry Prisms
C 1325-08b Standard Specification for Nonasbestos Fiber-mat
Reinforced Cement Interior Substrate Sheets
C 1328-05 Specification for Plastic (Stucco Cement
C 1386-07 Specification for Precast Autoclaved Aerated Concrete (AAC) Wall Construction
C 1395/C 1395M-06a Specification for Gypsum Ceiling Board C 1396M-09a Specification for Gypsum Board
C 1405-10 Standard Specification for Glazed Brick (Single Fired, Solid Brick Units
C 1492-03 (2009) Standard Specification for Concrete Roof
C 1629/C 1629M-06 Standard Classification for Abuse-resistant
Nondecorated Interior Gypsum Panel Products and Fiber-reinforced Cement Panels
C 1658/C 1658M-06 Standard Specification for Glass Mat Gypsum
Panels
D 25-99 (2005) Specification for Round Timber Piles
D 41-05 (2010) Specification for Asphalt Primer Used in Roofing,
Dampproofing and Waterproofing
D 43-00 (2006) Specification for Coal Tar Primer Used in Roofing,
Dampproofing and Waterproofing
D 56-05 Test Method for Flash Point By Tag Closed Tester
D 86-10a Test Method for Distillation of Petroleum Products at Atmospheric Pressure
D 93-10 Test Method for Flash Point ByPensky- MartensClosed Cup Tester
D 225-07 Specification for Asphalt Shingles (Organic Felt) Surfaced with Mineral Granules
D 226/D 226M-09 Specification for Asphalt-saturated Organic Felt
Used in Roofing and Waterproofing
D 227-03 Specification for Coal-tar-saturated Organic Felt Used in Roofing and Waterproofing
D 312-00 (2006) Specification for Asphalt Used in
D 422-63 (2007) Test Method for Particle-size Analysis of Soils
D 448-08 Standard Classification for Sizes of Aggregate for Road and Bridge
D 450-07 Specification for Coal-tar Pitch Used in Roofing, Dampproofing and Waterproofing
D 635-10 Test Method for Rate of Burning and/or Extent and Time of Burning of Self-supporting Plastics in a Horizontal Position
D 1143/D 1143M-07e1 Test Method for Piles Under Static Axial
Compressive Load
D 1227-95 (2007) Specification for Emulsified Asphalt Used as a
Protective Coating for Roofing
D 1557-09 Test Method for Laboratory Compaction Characteristics of Soil Using Modified Effort
3 3
[56,000 ft-lb/ft (2,700 KN m/m )]
D 1586-08a Specification for Penetration Test and Split-barrel
Sampling of Soils
D 1761-06 Test Method for Mechanical Fasteners in Wood
D 1863-05 Specification for Mineral Aggregate Used on Built- up Roofs
D 1929-96 (2001)e01 Test Method for Determining Ignition Properties of
Plastics
D 1970-09 Specification for Self-adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roof Underlayment for Ice Dam Protection
D 2166-06 Test Method for Unconfined Compressive Strength of Cohesive Soil
D 2178-04 Specification for Asphalt Glass Felt Used in Roofing and Waterproofing
D 2216-10 Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
D 2487-10 Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
D 2626-04 Specification for Asphalt Saturated and Coated Organic Felt Base Sheet Used in Roofing
D 2822-05 Specification for Asphalt Roof Cement
D 2823-05 Specification for Asphalt Roof Coatings
D 2843-10 Test for Density of Smoke from the Burning or Decomposition of Plastics
D 2850-03a (2007) Test Method for Unconsolidated, Undrained
Triaxial Compression Test on Cohesive Soils
D 2898-10 Test Methods for Accelerated Weathering of Fire- retardant-treated Wood for Fire Testing
D 3019-08 Specification for Lap Cement Used with Asphalt Roll Roofing, Nonfibered, Asbestos Fibered and NonasbestosFibered
D 3161-09 Test Method for a Wind Resistance of Asphalt Shingles (Fan Induced Method)
D 3200-74 (2005) Standard Specification and Test Method for
Establishing Recommended Design Stresses for Round Timber Construction Poles
D 3201-08ae1 Test Method for Hygroscopic Properties of Fire-
retardant-treated Wood and Wood-based Products D 3278-96(2004)e01 Test Methods for Flash Point of Liquids by Small
Scale Closed-cup Apparatus
D 3462/ D3462M-10a Specification for Asphalt Shingles Made from Glass
Felt and Surfaced with Mineral Granules
D 3468-99 (2006)e1 Specification for Liquid-applied Neoprene and
Chlorosulfonated Polyethylene Used in Roofing and Waterproofing
D 3679-09a Specification for Rigid Poly [Vinyl Chloride (PVC)
Siding]
D 3689-07 Method for Testing Individual Piles Under Static Axial Tensile Load
D 3737-09 Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)
D 3746-85 (2008) Test Method for Impact Resistance of Bituminous
Roofing Systems
D 3747-79 (2007) Specification for Emulsified Asphalt Adhesive for
Adhering Roof Insulation
D 3909-97b (2004)e01 Specification for Asphalt Roll Roofing (Glass Felt)
Surfaced with Mineral Granules
D 3957-09 Standard Practices for Establishing Stress Grades for Structural Members Used in Log Buildings
D 4022-07 Specification for Coal Tar Roof Cement, Asbestos Containing
D 4272-09 Test Method for Total Energy Impact of Plastic Films by Dart Drop
D 4318-10 Test Methods for Liquid Limit, Plastic Limit and Plasticity Index of Soils
D 4434/D 4434M-09 Specification for Poly (Vinyl Chloride) Sheet
Roofing
D 4479-07 Specification for Asphalt Roof Coatings- Asbestos-free
D 4586-07 Specification for Asphalt Roof Cement-Asbestos- free
D 4601-04 Specification for Asphalt-coated Glass Fiber Base Sheet Used in Roofing
D 4637/D 4637M-10 Specification forEPDMSheet Used in Single-ply
Roof Membrane
D 4829-08a Test Method for Expansion Index of Soils
D 4869-05e01 Specification for Asphalt-saturated (Organic Felt)
Underlayment Used in Steep Slope Roofing
D 4897/D 4897M-01(2009) Specification for Asphalt-coated Glass Fiber
Venting Base Sheet Used in Roofing
D 4945-08 Test Method for High-strain Dynamic Testing of Piles
D 4990-97a (2005)e1 Specification for Coal Tar Glass Felt Used in
Roofing and Waterproofing.
D 5019-07a Specification for Reinforced Nonvulcanized
Polymeric Sheet Used in Roofing Membrane
D 5055-10 Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-joists
D 5456-10 Specification for Evaluation of Structural Composite Lumber Products
D 5516-09 Test Method of Evaluating the Flexural Properties of Fire-retardant-treated Softwood Plywood Exposed to the Elevated Temperatures
D 5643-06 Specification for Coal Tar Roof Cement, Asbestos- free
D 5664-10 Test Methods for Evaluating the Effects of Fire- retardant Treatment and Elevated Temperatures on Strength Properties of Fire-retardant-treated Lumber
D 5665-99a (2006) Specification for Thermoplastic Fabrics Used in
Cold-applied Roofing and Waterproofing
D 5726-98 (2005) Specification for Thermoplastic Fabrics Used in
Hot-applied Roofing and Waterproofing .
D 6083-05e01 Specification for Liquid Applied Acrylic Coating
Used in Roofing
D 6162-00a (2008) Specification for Styrene-butadiene-styrene (SBS)
Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements
D 6163-00 (2008) Specification for Styrene-butadiene-styrene (SBS)
Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements
D 6164-05 e1 Specification for Styrene-butadiene-styrene (SBS)
Modified Bituminous Sheet Metal Materials Using Polyester Reinforcements
D 6222-08 Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements
D 6223/D6223M-02(2009)e1 Specification for Atactic Polypropylene (APP)
Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements
D 6298-05e1 Specification for Fiberglass Reinforced Styrene-
butadiene-styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface
D 6305-08 Practice for Calculating Bending Strength Design Adjustment Factors for Fire-retardant-treated Plywood Roof Sheathing
D 6380-03 (2009) Standard Specification for Asphalt Roll Roofing
(Organic) Felt
D 6509/D6509M-09 Standard Specification for Atactic Polypropylene
(APP) Modified Bituminous base Sheet Materials Using Glass Fiber Reinforcements
D 6694-08 Standard Specification for Liquid-applied Silicone Coating Used in Spray Polyurethane Foam Roofing
D 6754/D6754M-10 Standard Specification for Ketone Ethylene Ester Based Sheet Roofing
D 6757-07 Standard Specification for Inorganic Underlayment for Use with Steep Slope Roofing Products
D 6841-08 Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-retardant- treated Lumber
D 6878-08e1 Standard Specification for
ThermoplasticPolyolefinBased Sheet Roofing
D 6947-07 Standard Specification for Liquuid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System
D 7158-08d Standard Test Method for Wind Resistance of
Sealed Asphalt Shingles (Uplift Force/Uplift Resistance Method
E 84-10b Test Methods for Surface Burning Characteristics of Building Materials
E 90-09 Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
E 96/E 96M-05 Test Method for Water Vapor Transmission of
Materials
E 108-10a Test Methods for Fire Tests of Roof Coverings
E 119-10b Test Methods for Fire Tests of Building Construction and Materials
E 136-09b Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C
E 330-02 (2010) Test Method for Structural Performance of Exterior
Windows, Curtain Walls and Doors by Uniform Static Air Pressure Difference
E 331-00 (2009) Test Method for Water Penetration of Exterior
Windows, Skylights, Doors and Curtain Walls by Uniform Static Air Pressure Difference
E 492-09 Test Method for Laboratory Measurement of Impact Sound Transmission Through Floor-ceiling Assemblies Using the Tapping Machine
E 605-93 (2006) Test Method for Thickness and Density of Sprayed
Fire-resistive Material (SFRM) Applied to Structural Members.
E 681-09 Test Methods for Concentration Limits ofFlammabilityof Chemical Vapors and Gases
E 736-00 (2006) Test Method for Cohesion/Adhesion of Sprayed
Fire-resistive Materials Applied to Structural Members
E 814-10 Test Method of Fire Tests of Through-penetration Firestops
E 970-10 Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source
E 1300-09a Practice for Determining Load Resistance of Glass in Buildings.
E 1354-10a Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
E 1592-05 Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference
E 1602-03 (2010)e1 Guide for Construction of Solid Fuel-burning
Masonry Heaters
E 1886-05 Test Method for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Missiles and Exposed to Cyclic Pressure Differentials
E 1966-07 Test Method for Fire-resistant Joint Systems.
E 1996-09 Specification for Performance of Exterior Windows, Glazed Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
E 2072-10 Standard Specification for Photoluminescent (Phosphorescent) Safety Markings
E 2273-03 Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies
E 2307-10 Standard Test Method for Determining Fire Resistance of Perimeter Fire Barrier Systems Using Intermediate-scale, Multistory Test Apparatus
E 2404-10 Standard Practice for Specimen Preparation and Mounting of Textile, Paper or Vinyl Wall or Ceiling Coverings to Assess Surface Burning Characteristics
E 2568-09e1 Standard Specification for PB Exterior Insulation
and Finish Systems (EIFS)
E 2570-07 Standard Test Method for Evaluating Water- resistive Barrier (WRB) Coatings Used Under Exterior Insulation and Finish Systems (EIFS) for EIFS with Drainage
E 2573-07a Standard Practice for Specimen Preparation and Mounting of Site-fabricated Stretch Systems to Assess Surface Burning Characteristics
F 547-06 Terminology of Nails for Use with Wood and Wood-based Materials
F 1346-91 (2003) Performance Specification for Safety Covers and
Labeling Requirements for All Covers for Swimming Pools, Spas and Hot Tubs
F 1667-10 Specification for Driven Fasteners: Nails, Spikes and Staples
F 2006-10 Standard/Safety Specification for Window Fall Prevention Devices for NonemergencyEscape (Egress) and Rescue (Ingress) Windows
F 2090-10 Specification for Window Fall Prevention Devices with Emergency Escape (Egress) Release Mechanisms
F 2200-05 Standard Specification for Automated Vehicular Gate Construction
G 152-06 Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials
G 154-06 Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials
G 155-05a Practice for Operating Xenon Arc Light Apparatus for Exposure of Nonmetallic Materials
The Association of the Wall and Ceiling Industries International 513 West Broad Street, Suite 210
Falls Church, VA 22046
AWCI
Standard reference
number Title
12-B-05 Technical Manual 12-B Standard Practice for the Testing and Inspection of Field Applied Thin Film Intumescent Fire-resistive Materials; an Annotated Guide, Second Edition
American Wood Protection Association P.O. Box 361784
Birmingham, AL 35236-1784
AWPA
Standard
reference
number Title
C1-03 All Timber Products-Preservative Treatment by Pressure Processes
M4-06 Standard for the Care of Preservative-treated Wood Products U1-10 USE CATEGORY SYSTEM: User Specification for Treated
Wood Except Section 6, Commodity Specification H
American Welding Society 550 N.W. LeJeune Road Miami, FL 33126
AWS
Standard reference
number Title
D1.1-10 Structural Welding Code-Steel D1.3-08 Structural Welding Code-Sheet Steel
D1.4-05 Structural Welding Code-Reinforcing Steel
Builders Hardware Manufacturers' Association 355 Lexington Avenue, 17th Floor
New York, NY 10017-6603
BHMA
Standard reference
number Title
A 156.10-05 Power Operated Pedestrian Doors
A 156.19-07 Standard for Power Assist and Low Energy Operated Doors
Canadian General Standards Board Place du Portage 111, 6B1
11 Laurier Street
Gatineau, Quebec, Canada KIA 1G6
CGSB
Standard Reference
Number Title
37-GP-52M (1984) Roofing and Waterproofing Membrane, Sheet Applied, Elastomeric
37-GP-56M (1985) Membrane, Modified, Bituminous, Prefabricated
and Reinforced for Roofing-with December 1985 Amendment
CAN/CGSB 37.54-95 Polyvinyl Chloride Roofing and Waterproofing
Membrane
Composite Panel Association 19465 Deerfield Avenue, Suite 306
Leesburg, VA 20176
CPA
Standard reference
number Title
ANSI A135.4-2004 Basic Hardboard
ANSI A135.5-2004 Prefinished Hardboard Paneling ANSI A135.6-2006 Hardboard Siding
Consumer Product Safety Commission 4330 East West Highway
Bethesda, MD 20814-4408
CPSC
Standard reference
number Title
16 CFR Part 1201(1977) Safety Standard for Architectural Glazing Material
16 CFR Part 1209 (1979) Interim Safety Standard for Cellulose
Insulation
16 CFR Part 1404 (1979) Cellulose Insulation
16 CFR Part 1500 (1991) Hazardous Substances and Articles;
Administration and Enforcement Regulations
16 CFR Part 1500.44 (2001) Method for Determining Extremely
Flammable and Flammable Solids 16 CFR Part 1507 (2001) Fireworks Devices
16 CFR Part 1630 (2000) Standard for the Surface Flammability of
Carpets and Rugs
Canadian Standards Association 5060 Spectrum Way, Suite 100
Mississauga, Ontario, L4W 5N6 Canada
CSA
Standard reference
number Title
101/I.S.2/A440-08 Specifications for Windows, Doors and Unit
Skylights
Cedar Shake and Shingle Bureau P.O. Box 1178
Sumas, WA 98295-1178
CSSB
Standard reference
number Title
CSSB-97 Grading and Packing Rules for Western Red Cedar Shakes and Western Red Shingles of the Cedar Shake and Shingle Bureau
Door and Access Systems Manufacturers Association International 1300 Summer Avenue
Cleveland, OH 44115-2851
DASMA
Standard reference
number Title
ANSI/DASMA 107-1997
(R2004) Room Fire Test Standard for Garage Doors Using Foam Plastic Insulation
108-05 Standard Method for Testing Sectional Garage Doors and Rolling Doors: Determination of Structural Performance Under Uniform Static Air Pressure Difference
115-05 Standard Method for Testing Sectional Garage Doors and Rolling Doors: Determination of
Structural Performance Under Missile Impact and Cyclic Wind Pressure
U.S. Department of Commerce
National Institute of Standards and Technology 1401 Constitution Avenue, NW
Washington, DC 20230
DOC
Standard reference
number Title
PS-1-07 Structural Plywood
PS-2-04 Performance Standard for Wood-based Structural-use Panels
PS 20-05 American Softwood Lumber Standard
U.S. Department of Justice,
950 Pennsylvania Avenue, NW, Civil Rights Division, Disability Rights Section-NYA Washington, DC 20530
DOJ
Standard reference
number Title
See Section 3501.3
U.S. Department of Labor
c/o Superintendent of Documents U.S. Government Printing Office Washington, DC 20402-9325
DOL
Standard reference
number Title
29 CFR Part 1910.1000
(1974) Air Contaminants
U.S. Department of Transportation c/o Superintendent of Documents 1200 New Jersey Avenue, SE Washington, DC 20402-9325
DOTn
Standard reference
number Title
49CFRParts 100-185-2005 Hazardous Materials Regulations 49 CFR Parts 173.137
(2005) Shippers-General Requirements for Shipments and Packaging-Class 8-Assignment of Packing Group
49 CFR-1998 Specification of Transportation of Explosive and
Other Dangerous Articles,
UN 0335, UN 0336 Shipping Containers
European Committee for Standardization (EN) Central Secretariat
Rue de Stassart 36 B-10 50 Brussels
EN
Standard reference
number Title
EN 1081-98 Resilient Floor Coverings-Determination of the Electrical Resistance
Federal Emergency Management Agency Federal Center Plaza
500 C Street S.W. Washington, DC 20472
FEMA
Standard reference
number Title
FIA-TB11-01 Crawlspace Construction for Buildings Located in
Special Flood Hazard Areas
Factory Mutual Global Research Standards Laboratories Department 1301 Atwood Avenue, P.O. Box 7500 Johnson, RI 02919
FM
Standard reference
number Title
4450 (1989) Approval Standard for Class 1 Insulated Steel Deck Roofs-with Supplements through July 1992
4470 (2010) Approval Standard for Class 1 Roof Covers
4474 (04) Evaluating the Simulated Wind Uplift Resistance of Roof Assemblies Using Static Positive and/or Negative Differential Pressures
4880 (2010) American National Standard for Evaluating Insulated Wall or Wall and Roof/ Ceiling Assemblies, Plastic Interior Finish Materials, Plastic Exterior Building Panels, Wall/Ceiling Coating Systems, Interior and Exterior Finish Systems
Gypsum Association
810 First Street N.E. #510 Washington, DC 20002-4268
GA
Standard reference
number Title
GA 216-10 Application and Finishing of Gypsum Panel Products GA 600-09 Fire-resistance Design Manual, 18th Edition
Hardwood Plywood Veneer Association 1825 Michael Faraday Drive
Reston, VA 20190-5350
HPVA
Standard
reference
number Title
HP-1-2009 Standard for Hardwood and Decorative Plywood
U.S. Department of Housing and Urban Development 451 7th Street, SW,
Washington, DC 20410
HUD
Standard reference
number Title
HUD 24 CFR Part 3280 (1994) Manufactured Home Construction and Safety Standards
International Code Council, Inc. 500 New Jersey Ave, NW 6th Floor Washington, DC 20001
ICC
Standard reference
number Title
ICC/ANSI A117.1-03 Accessible and Usable Buildings and Facilities
ICC 300-07 ICC Standard on Bleachers, Folding and Telescopic
Seating and
ICC 400-07 Standard on Design and Construction of Log
Structures
ICC 500-08 ICC/NSSA Standard on the Design and Construction of Storm
ICC 600-08 Standard for Residential Construction in High Wind
Regions
IEBC - 09 International Existing Buildings Code
IECC-09 International Energy Conservation Code (adoption includes only section 101 of chapter 1 and chapters 2 through 6)
IFC-09 International Fire Code
IFGC-09 International Fuel Gas Code (including ICC Emergency Amendment changing IFGC Sections 406.7)
SBCCI SSTD 11-99 Test Standard for Determining Wind Resistance of
Concrete or Clay Roof Tiles
International Organization for Standardization ISO Central Secretariat,
1 ch, de la Voie-Creuse, Case Postale 56
CH-1211 Geneva 20, Switzerland
ISO
Standard reference
number Title
ISO 8115-86 Cotton Bales-Dimensions and Density
National Association of Architectural Metal Manufacturers, 800 Roosevelt Road,
Bldg. C, Suite 312 Glen Ellyn, IL 60137
NAAMM
Standard reference
number Title
FP 1001-07 Guide Specifications for Design of Metal Flag Poles
National Concrete Masonry Association, 13750 Sunrise Valley,
Herndon, VA 22071-4662
NCMA
Standard reference
number Title
TEK5-08 Details for Concrete Masonry Fire Walls
National Fire Protection Association 1 Batterymarch Park
Quincy, MA 02269-9101
NFPA
Standard reference
number Title
10-10 Portable Fire Extinguishers 11-10 Low Expansion Foam
12-08 Carbon Dioxide Extinguishing Systems
12A-04 Halon 1301 Fire Extinguishing Systems
13-10 Installation of Sprinkler Systems (including TIA 10- 1)
13D-10 Installation of Sprinkler Systems in One- and Two- family Dwellings and Manufactured Homes
13R-10 Installation of Sprinkler Systems in Residential Occupancies Up to and Including Four Stories in Height
14-10 Installation of Standpipe and Hose System
16-07 Installation of Foam-water Sprinkler and Foam- water Spray Systems
17-09 Dry Chemical Extinguishing Systems 17A-09 Wet Chemical Extinguishing
20-10 Installation of Stationary Pumps for Fire Protection
30-08 Flammable and Combustible Liquids Code
31-06 Installation of Oil-burning Equipment 32-07 Dry Cleaning Plants
40-11 Storage and Handling of Cellulose Nitrate Film 58-11 Liquefied Petroleum Gas Code
61-08 Prevention of Fires and Dust Explosions in Agricultural and Food Product Facilities
70-11 National Electrical Code 72-10 National Fire Alarm Code
80-10 Fire Doors and Other Opening Protectives
85-07 Boiler and Combustion System Hazards Code
(Note: NFPA 8503 has been incorporated into
NFPA 85)
92B-09 Smoke Management Systems in Malls, Atria and Large Spaces
99-05 Standard for Health Care Facilities
105-10 Standard for the Installation of Smoke Door Assemblies
110-10 Emergency and Standby Power Systems
111-10 Stored Electrical Energy Emergency and Standby Power Systems
120-10 Coal Preparation Plants
170-09 Standard for Fire Safety and Emergency Symbols
211-10 Chimneys, Fireplaces, Vents and Solid Fuel- burning
252-08 Standard Methods of Fire Tests of Door Assemblies
253-06 Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source
257-07 Standard for Fire Test for Window and Glass Block Assemblies
259-08 Test Method for Potential Heat of Building Materials
265-07 Method of Fire Tests for Evaluating Room Fire Growth Contribution of Textile Wall Coverings on Full Height Panels and Walls
268-07 Standard Test Method for Determining Ignitibility of Exterior Wall Assemblies Using a Radiant Heat Energy Source
285-06 Standard Method of Test for the Evaluation of Flammability Characteristics of Exterior Nonload- bearingWall Assemblies Containing Combustible Components
286-06 Standard Method of Fire Test for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth
288-07 Standard Method of Fire Tests of Floor Fire Door Assemblies Installed Horizontally in Fire- resistance-rated Floor Systems
409-11 Aircraft Hangars 418-06 Standard for Heliports 484-09 Combustible Metals
654-06 Prevention of Fire & Dust Explosions from the Manufacturing, Processing and Handling of Combustible Particulate Solids
655-07 Prevention of Sulfur Fires and Explosions
664-07 Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities
701-10 Standard Methods of Fire Tests for Flame- propagation of Textiles and Films
704-07 Standard System for the Identification of the Hazards of Materials for Emergency Response
1124-06
Manufacture, Transportation and Storage
of
Fireworks and Pyrotechnic Articles
2001-08
Clean Agent Fire Extinguishing Systems
Precast Prestressed Concrete Institute 175 W. Jackson Boulevard, Suite 500 Chicago, IL 60604-6938
PCI
Standard reference
number Title
MNL 124-89 Design for Fire Resistance of Precast Prestressed
Concrete
MNL 128-01 Recommended Practice for Glass Fiber Reinforced
Concrete Panels
Post-Tensioning Institute
8601 North Black Canyon Highway, Suite 103 Phoenix, AZ 85021
PTI
Standard reference
number Title
PTI-2008 Standard Requirements for Analysis of Shallow Concrete Foundations on Expansive Soils, Third Edition
PTI-2008 Standard Requirements for Design of Shallow Post- tensioned Concrete Foundation on Expansive Soils, Second Edition
Rack Manufacturers Institute
8720 Red Oak Boulevard, Suite 201 Charlotte, NC 28217
RMI
Standard reference
number Title
ANSI/MH16.1-08 Specification for Design, Testing and Utilization of
Industrial Steel Storage Racks
Steel Deck Institute, P. O. Box 25
Fox River Grove, IL 60021
SDI
Standard reference
number Title
ANSI/NC1.0-06 Standard for Noncomposite Steel Floor Deck ANSI/RD1.0-06 Standard for Steel Roof Deck
Steel Joist Institute,
1173B London Links Drive Forest, VA 24551
SJI
Standard reference
number Title
CJ-1.0-06 Standard Specification for Composite Steel Joists, CJ-series
JG-1.1-05 Standard Specification for Joist Girders
K-1.1-05 Standard Specification for Open Web Steel Joists, K- series
LH/DLH-1.1-05 Standard Specification for Longspan Steel Joists,
LH-series and Deep Longspan Steel Joists, DLH- series
Single-Ply Roofing Institute,
411 Waverly Oaks Road, Suite 331B, Waltham, MA 02452
SPRI
Standard reference
number Title
SPRI/ANSI/ES-1-03 Wind Design Standard for Edge Systems Used with
Low Slope Roofing Systems
RP-4-02 Wind Design Guide for Ballasted Single-ply Roofing Systems
Telecommunications Industry Association 2500 Wilson Boulevard
Arlington, VA 22201-3834
TIA
Standard reference
number Title
TIA-222-G-09 Structural Standards for Steel Antenna Towers and Antenna Supporting Structures including-Addendum 1, 222-G-1, Dated 2007
The Masonry Society,
3970 Broadway, Unit 201-D, Boulder, CO 80304-1135
TMS
Standard reference
number Title
0216-07 Standard Method for Determining Fire Resistance of Concrete and Masonry Construction Assemblies
0302-07 Standard Method for Determining the Sound Transmission Class Rating for Masonry Walls
402-08 Building Code Requirements for Masonry Structures 602-08 Specification for Masonry Structures
Truss Plate Institute,
218 N. Lee Street, Suite 312 Alexandria, VA 22314
TPI
Standard reference
number Title
TPI 1-2007 National Design Standards for Metal-plate-connected Wood Truss Construction
Underwriters Laboratories, Inc. 333 Pfingsten Road
Northbrook, IL 60062-2096
UL
Standard reference
number Title
9-09 Fire Tests of Window Assemblies 10A-09 Tin Clad Fire Doors
10B-08 Fire Tests of Door Assemblies
10C-09 Positive Pressure Fire Tests of Door Assemblies
14B-08 Sliding Hardware for Standard Horizontally-mounted Tin Clad Fire Doors
14C-06 Swinging Hardware for Standard Tin Clad Fire Doors Mounted Singly and in Pairs
103-10 Factory-built Chimneys, for Residential Type and Building Heating Appliances
127-08 Factory-built Fireplaces
199E-04 Outline of Investigation for Fire Testing of Sprinklers and Water Spray Nozzles for Protection of Deep Fat Fryers.
217-06 Single and Multiple Station Smoke Alarms
263-03 Standard for Fire Test of Building Construction and Materials
268-09 Smoke Detectors for Fire Protective Signaling Systems 300-05 Fire Testing of Fire Extinguishing Systems for Protection
of Restaurant Cooking Areas 305-97 Panic Hardware
325-02 Door, Drapery, Gate, Louver and Window Operations and Systems-with Revisions through February 2006
555-2006 Fire Dampers 555C-2006 Ceiling Dampers
555S-99 Smoke Dampers-with Revisions through July 2006 580-2006 Test for Uplift Resistance of Roof Assemblies 641-95 Type L Low-temperature Venting Systems
710B-04 Recirculating Systems-with Revisions through April 2006 723-08 Standard for Test for Surface Burning Characteristics of
Building Materials
790-04 Standard Test Methods for Fire Tests of Roof Coverings 793-08 Standards for Automatically Operated Roof Vents for
Smoke and Heat
864-03 Standards for Control Units and Accessories for Fire Alarm Systems-with Revisions through March 2006
924-06 Standard for Safety Emergency Lighting and Power Equipment
1040-96 Fire Test of Insulated Wall Construction-with Revisions through June 2001
1256-02 Fire Test of Roof Deck Construction-with Revisions through January 2007
1479-03 Fire Tests of Through-penetration Firestops-with Revisions through April 2007
1482-10 Solid-fuel-type Room Heater
1715-97 Fire Test of Interior Finish Material-with Revisions through March 2004
1777-07 Chimney Liners
1784-01 Air Leakage Tests of Door Assemblies-with Revisions through December 2004
1897-04 Uplift Tests for Roof Covering Systems
1975-06 Fire Test of Foamed Plastics Used for Decorative Purposes 1994-04 Standard for Luminous Egress Path Marking Systems-
with Revisions through February 2005
2017-08 Standards for General-purpose Signaling Devices and Systems
2079-04 Tests for Fire Resistance of Building Joint Systems-with Revisions through March 2006
2200-98 Stationary Engine Generator Assemblies
Underwriters Laboratories of Canada, 7 Underwriters Road,
Toronto, Ontario, Canada M1R3B4
ULC
Standard reference
number Title
CAN/ULC S102.2-2010 Standard Method of Test for Surface Burning
Characteristics of Flooring, Floor Coverings and Miscellaneous Materials and Assemblies-with 2000 Revisions
United States Code,
c/o Superintendent of Documents U.S. Government Printing Office, Washington, DC 20402-9325
USC
Standard reference
number Title
10 U.S.C. Sections 18233(A)(1) and 18237-1994
18 USC Part 1, Ch.40 Importation, Manufacture, Distribution and Storage of Explosive Materials
Window and Door Manufacturers Association 1400 East Touhy Avenue #470
Des Plaines, IL 60018
WDMA
Standard reference
number Title
AAMA/WDMA/CSA
101/I.S.2/A440-08 Specifications for Windows, Doors and Unit
Skylights
Wire Reinforcement Institute, Inc. 942 Main Street, Suite 300 Hartford, CT 06103
WRI
Standard reference
number Title
WRI/CRSI-81 Design of Slab-on-ground Foundations-with 1996 Update
Replaces: 4101:1-35-01
Effective: 11/01/2011
R.C. 119.032 review dates: 11/01/2016
CERTIFIED ELECTRONICALLY
Certification
04/18/2011
Date
Promulgated Under: 119.03
Statutory Authority: 3781.10(A)
Rule Amplifies: 3781.10, 3781.11, 3791.04
Prior Effective Dates: 9/1/92, 2/1/93, 7/1/95, 7/1/97, 3/1/98, 7/1/98, 1/1/99,
12/1/00, 1/1/02, 3/1/05, 9/6/05, 3/1/06, 7/1/07, 1/1/08,
3/31/08(Emer.), 6/24/08, 1/1/09
Document Information
- Effective Date:
- 11/1/2011
- File Date:
- 2011-04-18
- Last Day in Effect:
- 2011-11-01
- Rule File:
- 4101$1-35-01_PH_FF_N_RU_20110418_1139.pdf
- Related Chapter/Rule NO.: (1)
- Ill. Adm. Code 4101:1-35-01. Referenced standards