4101:8-44-01 Referenced standards.

 

 

 

 

 

 

4101:8-44-01  Referenced standards.

 

SECTION 4401 REFERENCED STANDARDS

 

                                                                           General. This chapter lists the standards that are referenced in various sections of this code. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and title. The application of the referenced standards shall be as specified in Section 102.5.

 

                                                                          Referenced codes. When indicated in this code, the following codes refer to provisions in the listed chapters of the administrative code:

Referenced Code	Ohio Administrative Code Chapters
Ohio Building Code	4101:1-1 to 4101:1-35
Fire Code	1301:7-1 to 1301:7-7
Mechanical Code	4101:2-1 to 4101:2-15
Plumbing Code	4101:3-1     to      4101:3-13,
	codified  and  published  as
	the   2011   Ohio   Plumbing
	Code,   effective   11-1-2011
	(including  update  effective
	03-15-2012),        and         as
	modified         in         Section
	2501.1.1.

 

                              Referenced standard list.

 

American Architectural Manufacturers Association 1827 Walden Office Square, Suite 550

Schaumburg, IL 60173

 

AAMA

Standard reference

number                                   Title

AAMA/WDMA/CSA

 

 

 

 

 

 

 

 

 

101/I.S.2/A440-08               North American Fenestration

Standards/Specifications for Windows, Doors and Skylights

450-10                                  Voluntary Performance Rating Method for Mulled Fenestration Assemblies

506-08                                  Voluntary Specifications for Hurricane Impact and Cycle Testing of Fenestration Products

711-07                                  Voluntary Specification for Self Adhering Flashing Used for Installation of Exterior Wall Fenestration Products.

Air Conditioning Contractors of America 2800 Shirlington Road, Suite 300

Arlington, VA 22206

ACCA

Standard reference

number                                   Title

Manual D-09                        Residential Duct Systems

Manual J- 04                         Residential Load Calculation-Eighth Edition Manual S-04                                                Residential Equipment Selection

American Concrete Institute 38800 Country Club Drive Farmington Hills, MI 48331

ACE

Standard reference

number                       Title

318-08                      Building Code Requirements for Structural Concrete 332-08             Code Requirements for Residential Concrete Construction 530-08             Building Code Requirements for Masonry Structures 530.1-08                      Specification for Masonry Structures

American Forest and Paper Association 1111 19th Street, NW, Suite 800

Washington, DC 20036

American Forest Products Association (Currently the American Wood Council) 803 Sycolin Road, Suite 201

Leesburg, VA 20175 http://www.awc.org/index.html

AFPA

Standard reference

number                       Title

NDS-05                    National Design Specification (NDS) for Wood

Construction-with 2005 Supplement

WFCM-01                   Wood Frame Construction Manual for One- and Two- family Dwellings

AFPA-93                  Span Tables for Joists and Rafters

PWF-07                    Permanent Wood Foundation Design Specification

American Iron and Steel Institute 1140 Connecticut Ave, Suite 705

Washington, DC 20036

AISI

Standard reference

number                                   Title

AISI S100-07                       North  American  Specification  for  the  Design  of

Cold-formed Steel Structural Members

AISI S230-07                       Standard     for      Cold-formed     Steel      Framing-

prescriptive   Method   for   One-   and   Two-family Dwellings

American Institute of Timber Construction 7012 S. Revere Parkway, Suite 140

Centennial, CO 80112

AITC

Standard reference

number                                               Title

ANSI/AITC A 190.1-07                  Structural Glued Laminated Timber American National Standards Institute

25 West 43rd Street, Fourth Floor New York, NY 10036

ANSI

Standard reference

number                                   Title

A108.1A-09                         Installation of Ceramic Tile in the Wet-set Method,

with Portland Cement Mortar

A108.1B-09                         Installation of Ceramic Tile, Quarry Tile on a Cured

Portland Cement Mortar Setting Bed with Dry-set or Latex-Portland Mortar

A108.4-09                            Installation of Ceramic Tile with Organic Adhesives or Water Cleanable Tile-setting Epoxy Adhesive

A108.5-09                            Installation  of  Ceramic  Tile  with  Dry-set  Portland Cement Mortar or Latex-Portland Cement Mortar

A108.6-09                            Installation    of    Ceramic    Tile    with    Chemical- resistant, Water-cleanable Tile-setting and -grouting Epoxy

A108.11-09                          Interior Installation of Cementitious Backer Units A118.1-10.1                                                American National Standard Specifications for Dry-

set Portland Cement Mortar

A118.3-10.1                         American   National   Standard   Specifications   for

Chemical-resistant,  Water-cleanable  Tile-setting and Grouting Epoxy and Water-cleanable Tile- setting Epoxy Adhesive

A118.10-10.1                       Specification      for      Load      Bearing,      Bonded,

Waterproof Membranes for Thin-set Ceramic Tile and Dimension Stone Installation

A136.1-10.1                         American   National   Standard   Specifications   for

Organic Adhesives for Installation of Ceramic Tile

A137.1-08                            American   National   Standard   Specifications   for Ceramic Tile

A208.1-09                            Particleboard

LC1-05                                 Interior Fuel Gas Piping Systems Using Corrugated Stainless Steel Tubing

LC4-07                                 Press-connect Copper and Copper Alloy Fittings for use in Fuel Gas Distribution Systems

Z21.1-05                               Household Cooking Gas Appliances

Z21.5.1-06                            Gas  Clothes  Dryers-Volume  I-Type  I  Clothes Dryers

Z21.8-94 (R2002)                Installation of Domestic Gas Conversion Burners Z21.10.1-09                                                Gas  Water  Heaters-Volume  I-Storage  Water

Heaters with Input Ratings of 75,000 Btu per hour or Less

Z21.10.3-07                          Gas  Water  Heaters-Volume  III-Storage  Water

Heaters with Input Ratings above 75,000 Btu per hour, Circulating and Instantaneous Water Heaters

Z21.11.2-07                          Gas-fired  Room  Heaters-Volume  II-Unvented

Room Heaters

Z21.13-10                             Gas-fired   Low-Pressure   Steam  and   Hot   Water Boilers

Z21.15- 09                              Manually  Operated  Gas  Valves  for  Appliances, Appliance Connector Valves and Hose End Valves

Z21.24- 06                              Connectors for Gas Appliances

Z21.40.1-96 (R2002)           Gas-fired,   Heat-activated   Air   Conditioning   and

Heat    Pump     Appliances-    with     Z21.40.1a-97 (R2002)

Z21.40.2-96 (R2002)           Gas-fired,  Work-activated  Air  Conditioning  and

Heat  Pump  Appliances  (Internal  Combustion)  - with Z21.40.2a-1997 (R2002)

Z21.42-04                             Gas-fired Illuminating Appliances

Z21.47-06                             Gas-fired Central Furnaces

Z21.50-07                             Vented Gas Fireplaces

Z21.56-06                             Gas-fired Pool Heaters

Z21.58-08                             Outdoor Cooking Gas Appliances

Z21.60-03                             Decorative Gas Appliances for Installation in Solid Fuel Burning Fireplaces-with Addenda Z21.60a- 2003

Z21.75/CSA6.27-07             Connectors for Outdoor Gas Appliances Z21.80-03                                                Line Pressure Regulators

Z21.83-98                             Fuel Cell Power Plants.

Z21.84-02                             Manually Listed, Natural Gas Decorative Gas Appliances for Installation in Solid Fuel-burning Fireplaces-with Addenda Z21.84a -2003

Z21.86-08                             Gas-fired Vented Space Heating Appliances

Z21.88-09                             Vented Gas Fireplace Heaters

Z21.91-07                             Ventless     Firebox     Enclosures      for      Gas-fired Unvented Decorative Room Heaters

Z83.6-90 (R1998)                Gas-fired Infrared Heaters

Z83.8-09                               Gas-fired Unit Heaters and Gas-fired Duct Furnaces

Z97.1-09                               Safety Glazing Materials Used in  Buildings- Safety Performance Specifications and Methods of Test

APA-The Engineered Wood Association 7011 South 19th

Tacoma, WA 98466

APA

Standard reference

number                       Title

APA E30-07 Engineered Wood Construction Guide

American Society of Civil Engineers Structural Engineering Institute 1801 Alexander Bell Drive

Reston, VA 20191

ASCE/SEI

Standard reference

number                       Title

5-08                          Building Code Requirements for Masonry Structures

6-08                          Specification for Masonry Structures

7-05                          Minimum Design Loads for Buildings and Other Structures 24-05                                        Flood-resistant Design and Construction.

32-01                        Design    and   Construction    of    Frost-protected   Shallow Foundations

American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. 1791 Tullie Circle, NE

Atlanta, GA 30329

ASHRAE

Standard reference

number                       Title

34-10                        Designation and Safety Classification of Refrigerants ASHRAE-09                                    ASHRAE Fundamentals Handbook-2009

American Society of Mechanical Engineers Three Park Avenue

New York, NY 10016-5990

ASME

Standard reference

number                                               Title

A17.1/CSA B44-04                         Safety Code for Elevators and Escalators

A18.1-03                                          Safety Standard for Platforms and Stairway Chair Lifts

B1.20.1-1983 (R2006)                     Pipe Threads, General Purpose (Inch) B16.33-2002 (R2007)                                                            Manually Operated Metallic Gas Valves for

Use in Gas Piping Systems up to 125 psig (Sizes ½ through 2)

B16.44-02                                           Manually Operated Metallic Gas Valves For Use in Above-ground Piping Systems up to 5 psi.

B36.10M-2004                                 Welded and Seamless Wrought-steel Pipe

BPVC-2004                                     ASME Boiler and Pressure Vessel Code

CSD-1-09                                           Controls        and       Safety      Devices        for Automatically Fired Boilers

American Society of Sanitary Engineering 901 Canterbury, Suite A

Westlake, OH 44145

ASTM International 100 Barr Harbor Drive

West Conshohocken, PA 19428

ASTM

Standard reference

number                                   Title

A 36/A 36M-08                    Specification for Carbon Structural Steel

A 53/A 53M-10a                  Specification for Pipe, Steel, Black and Hot-dipped,

Zinc-coated Welded and Seamless

A 82/A 82M-07                    Specification  for  Steel  Wire,  Plain,  for  Concrete

Reinforcement

A 106/A 106M-10                Specification for Seamless Carbon Steel Pipe for

High Temperature Service

A 153/A 153M-09                Specification for Zinc Coating (Hot Dip) on Iron

and Steel Hardware

A 167-09                              Specification    for     Stainless    and     Heat-resisting Chromium-nickel Steel Plate, Sheet and Strip

A 240/A 240M-10a              Standard     Specification     for     Chromium      and

Chromium-nickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels and for General Applications

A 254-9707                          Specification for Copper Brazed Steel Tubing

A 307-07b                            Specification  for  Carbon  Steel  Bolts  and  Studs, 6000 psi Tensile Strength

A 463/A 463M-09a              Standard Specification for Steel Sheet, Aluminum-

coated by the Hot-dip Process.

A 510-08                              Specification  for  General  Requirements  for  Wire Rods and Coarse Round Wire, Carbon Steel

A 539-99                              Specification for Electric-resistance-welded Coiled Steel Tubing for Gas and Fuel Oil Lines

A 615/A 615M-09b              Specification  for  Deformed  and  Plain  Billet-steel

Bars for Concrete Reinforcement

A 641/A 641M-09b              Specification for Zinc-coated (Galvanized) Carbon

Steel Wire

A 653/A 653M-09a              Specification      for      Steel     Sheet,       Zinc-coated

(Galvanized)        or         Zinc-iron        Alloy-coated (Galvanized) by the Hot-dip Process

A 706/A 706/M-09b             Specification  for  Low-alloy  Steel  Deformed  and

Plain Bars for Concrete Reinforcement

A 755/A 755M-03 (2008)    Specification for Steel Sheet, Metallic Coated by

the Hot-dip Process and Prepainted by the Coil- coating Process for Exterior Exposed Building Products

A 778-01 (2009)e1               Specification  for  Welded  Unannealed  Austenitic

Stainless Steel Tubular Products

A 792/A 792M-09a              Specification for Steel Sheet, 55% Aluminum-zinc

Alloy-coated by the Hot-dip Process

A 875/A 875M-09a              Specification for Steel Sheet, Zinc-5%, Aluminum

Alloy-coated by the Hot-dip Process

A 924/A 924M-10                Standard  Specification  for  General  Requirements

for  Steel  Sheet,  Metallic-coated  by  the  Hot-Dip Process

A 951-06                              Specification    for     Steel    Wire    Masonry    Joint Reinforcement

A 996/A 996M-09b              Specifications     for      Rail-steel       and      Axel-steel

Deformed Bars for Concrete Reinforcement

A 1003/A 1003M-10            Standard  Specification  for  Steel  Sheet,  Carbon,

Metallic  and  Nonmetallic-coated  for  Cold-formed Framing Members

B 42-10                                Specification for Seamless Copper Pipe, Standard Sizes

B 43-09                                Specification    for     Seamless     Red    Brass      Pipe, Standard Sizes

B 75-02                                Specification for Seamless Copper Tube

B 88-09                                Specification for Seamless Copper Water Tube

B 101-07                              Specification  for  Lead-coated  Copper  Sheet  and Strip for Building Construction.

B 135-10                              Specification for Seamless Brass Tube

B 209-07                              Specification  for  Aluminum  and  Aluminum-alloy Sheet and Plate

B 227-10                              Specification  for  Hard-drawn  Copper-clad  Steel Wire

B 251-10                              Specification     for      General     Requirements     for Wrought Seamless Copper and Copper-alloy Tube

B 302-07                              Specification for Threadless Copper Pipe, Standard Sizes

B 306-09                              Specification for Copper Drainage Tube (DWV)

B 370-09                              Specification   for   Copper   Sheet   and   Strip   for Building Construction

B 447-07                              Specification for Welded Copper Tube

B 695-04 (2009)                   Standard   Specification    for    Coatings      of    Zinc

Mechanically Deposited on Iron and Steel

B 813-10                              Specification for Liquid and Paste Fluxes for Soldering Applications of Copper and Copper Alloy Tube

C 5-10                                  Specification for Quicklime for Structural Purposes C 27-98 (2008)                                                Specification for Standard Classification of Fireclay

and High-alumina Refractory Brick C 28/C 28M-10                                                Specification for Gypsum Plasters

C 33-08                                Specification for Concrete Aggregates

C 34-08                                Specification for Structural Clay Load-bearing Wall Tile C 35-01(2005) Specification for Inorganic Aggregates for Use in Gypsum Plaster

C 36/C 36M-03                    Specification for Gypsum Wallboard C 37/C 37M-01                                                Specification for Gypsum Lath

C 55-09                                Specification for Concrete Building Brick

C 59/C 59M-00 (2006)         Specification  for  Gypsum  Casting  and  Molding

Plaster

C 61/C 61M-00 (2006)         Specification for Gypsum Keene's Cement

C 62-10                                Specification  for  Building  Brick  (Solid  Masonry Units Made from Clay or Shale)

C 73-05                                Specification for Calcium Silicate Face Brick (Sand Lime Brick)

C 79-04a                               Specification for Treated Core and Nontreated Core Gypsum Sheathing Board

C 90-09                                Specification for Load-bearing Concrete Masonry Units

C 91-05                                Specification for Masonry Cement

C 94/C 94M-10                    Specification for Ready-mixed Concrete

C 129-06                              Specification      for      Nonload-bearing      Concrete Masonry Units

C 143/C 143M-10a              Test  Method  for  Slump  or  Hydraulic  Cement

Concrete

C 145-85                              Specification    for    Solid    Load-bearing      Concrete Masonry Units

C 150-09                              Specification for Portland Cement

C 199-84 (2005)                   Test Method for Pier Test for Refractory Mortar

C 203-05a                                 Standard Test Methods for Breaking Load and Flexural Properties of Block-type Thermal Insulation

C 207-06                                   Specification   for   Hydrated   Lime   for   Masonry Purposes

C 208-08a                            Specification for Cellulosic Fiber Insulating Board

C 216-10                              Specification  for  Facing  Brick  (Solid  Masonry Units Made from Clay or Shale)

C 270-10                              Specification for Mortar for Unit Masonry

C 272-01 (2007)                   Standard  Test  Method  for  Water  Absorption  of

Core      Materials       for      Structural      Sandwich Constructions

C 273-07a                            Standard  Test  Method  for  Shear  Properties  of Sandwich Core Materials

C 315-07                                   Specification  for  Clay  Flue  Liners  and  Chimney Pots

C 406-10                              Specifications for Roofing Slate

C 411-05                                   Test Method for Hot-surface Performance of High- temperature Thermal Insulation

C 475/C 475-02(2007)         Specification for Joint Compound and Joint Tape

for Finishing Gypsum Wallboard

C 476-10                              Specification for Grout for Masonry

C 514-04 (2009)e1               Specification   for   Nails   for   the   Application  of

Gypsum Wallboard

C 552-07                              Standard Specification for Cellular Glass Thermal Insulation

C 557-03 (2009)e1               Specification for Adhesives for Fastening Gypsum

Wallboard to Wood Framing

C 578-10                              Specification    for     Rigid,     Cellular      Polystyrene Thermal Insulation

C 587-04 (2009)                   Specification for Gypsum Veneer Plaster

C 588/C 588M-03e1            Specification for Gypsum Base for Veneer Plasters C 595-10                                                Specification for Blended Hydraulic Cements

C 630/C 630M-03                Specification for Water-resistant Gypsum Backing

Board

C 631-09                              Specification for Bonding Compounds for Interior Gypsum Plastering

C 645-09a                            Specification    for     Nonstructural       Steel     Framing Members

C 652-10                              Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale)

C 685-10                              Specification  for  Concrete  Made  by  Volumetric Batching and Continuous Mixing

C 728-05 (2010)                   Standard     Specification     for     Perlite       Thermal

Insulation Board

C 836/C836M-10                    Specification for High Solids Content, Cold Liquid-

applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course

C 843-99 (2006)                   Specification  for  Application  of  Gypsum  Veneer

Plaster

C 844-10                              Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster

C 847-10a                            Specification for Metal Lath

C 887-05 (2010)                   Specification     for     Packaged,       Dry,     Combined

Materials for Surface Bonding Mortar

C 897-05 (2009)                   Specification for Aggregate for Job-mixed Portland Cement-based Plasters

C 920-10                              Standard Specification for Elastomeric Joint Sealants

C 926-06                              Specification for Application of Portland Cement- based Plaster

C 931/C 931M-04                Specification for Exterior Gypsum Soffit Board C 933-09                                                Specification for Welded Wire Lath

C 954-10                              Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness

C 955-09a                            Specification for Load-bearing (Transverse and Axial) Steel Studs, Runners (Tracks), and Bracing or Bridging for Screw Application of Gypsum Panel Products and Metal Plaster Bases

C 957-10                              Specification for High-solids Content, Cold Liquid- applied Elastomeric Waterproofing Membrane for Use with Integral Wearing Surface

C 960-04                              Specification for Predecorated Gypsum Board

C 1002-07                            Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases

C 1029-10                            Specification for Spray-applied Rigid Cellular Polyurethane Thermal Insulation

C 1032-06                            Specification for Woven Wire Plaster Base

C 1047-10a                          Specification      for      Accessories      for     Gypsum

Wallboard and Gypsum Veneer Base

C 1063-08                            Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement- based Plaster.

C 1107-08                            Standard Specification for Packaged Dry, Hydraulic-cement Grout (Nonshrink)

C 1116-10                            Standard Specification for Fiber-reinforced Concrete and Shotcrete

C 1167-03 (2009)                 Specification for Clay Roof Tiles

C 1177/C 1177M-08            Specification for Glass Mat Gypsum Substrate for

Use as Sheathing

C 1178/C 1178M-08            Specification for Glass Mat Water-resistant Gypsum Backing Panel

C 1186-08                            Specification for Flat Nonasbestos Fiber Cement Sheets

C 1261-10                            Specification  for  Firebox  Brick  for  Residential Fireplaces

C 1278/C 1278M-07a          Specification for Fiber-reinforced Gypsum Panels C 1283-07a                                                Practice for Installing Clay Flue Lining

C 1288-99(2010)                  Standard  Specification  for  Discrete  Nonasbestos

Fiber-cement Interior Substrate Sheets

C 1289-10                            Standard  Specification  for  Faced  Rigid  Cellular Polyisocyanurate Thermal Insulation Board

C 1325-08b                          Standard  Specification  for  Nonasbestos  Fiber-mat

Reinforced Cement Interior Substrate Sheets.

C 1328-05                            Specification for Plastic (Stucco) Cement. C 1395/C 1395M-06a                           Specification for Gypsum Ceiling Board C 1396/C 1396M-09a                           Specification for Gypsum Board.

C 1492-03(2009)                  Specification for Concrete Roof Tile

C 1513-10                            Standard Specification for Steel Tapping Screws for Cold-formed Steel Framing Connections

C 1658/C 1658M-06            Standard   Specification   for   Glass   Mat   Gypsum

Panels

D 41-05 (2010)                     Specification for Asphalt Primer Used in Roofing,

Dampproofing and Waterproofing

D 43-00(2006)                      Specification for Coal Tar Primer Used in Roofing,

Dampproofing and Waterproofing

D 225-07                              Specification  for  Asphalt  Shingles  (Organic  Felt) Surfaced with Mineral Granules

D 226/D 226M-09                Specification  for  Asphalt-saturated  (Organic  Felt)

Used in Roofing and Waterproofing

D 227-03                              Specification for Coal Tar Saturated (Organic Felt) Used in Roofing and Waterproofing

D 312-00(2006)                    Specification for Asphalt Used in Roofing.

D 422-63 (2007)                   Test Method for Particle-size Analysis of Soils

D 449-03 (2008)                   Specification  for  Asphalt  Used  in  Dampproofing

and Waterproofing.

D 450-07                              Specification for Coal-tar Pitch Used in Roofing, Dampproofing and Waterproofing

D 1227-95(2007)                  Specification  for  Emulsified  Asphalt  Used  as  a

Protective Coating for Roofing

D 1248-05                            Specification  for  Polyethylene  Plastics  Extrusion Materials for Wire and Cable

D 1622-08                            Standard  Test  Method  for  Apparent  Density  of Rigid Cellular Plastics

D 1623-09                            Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics

D 1693-08                            Test Method for Environmental Stress-cracking of Ethylene Plastics

D 1784-08                            Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds

D 1863-05                            Specification for Mineral Aggregate Used in Built- up Roofs

D 1970-09                            Specification for Self-adhering Polymer Modified Bitumen Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection

D 2126-09                            Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging

D 2178-04                            Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

D 2412-10                            Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-plate Loading

D 2447-03                            Specification for Polyethylene (PE) Plastic Pipe Schedules 40 and 80, Based on Outside Diameter

D 2513-09a                          Specification for Thermoplastic Gas Pressure Pipe,

Tubing and Fittings

D 2559-10a                          Standard Specification for Adhesives for Structural

Laminated Wood Products for Use Under Exterior (West Use) Exposure Conditions

D 2626-04                            Specification for Asphalt-saturated and Coated Organic Felt Base Sheet Used in Roofing

D 2683-10                            Specification for Socket-type Polyethylene Fittings for Outside Diameter-controlled Polyethylene Pipe and Tubing

D 2822-05                            Specification for Asphalt Roof Cement

D 2823-05                            Specification for Asphalt Roof Coatings

D 2824-06                            Specification for Aluminum-pigmented Asphalt Roof Coatings, Nonfibered, Asbestos Fibered and Fibered without Asbestos

D 2837-08                            Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products

D 2846/D 2846M-09b          Specification for Chlorinated Poly (Vinyl Chloride)

(CPVC) Plastic Hot- and Cold-water Distribution Systems

D 2898-10                            Test Methods for Accelerated Weathering of Fire- retardant-treated Wood for Fire Testing

D 3019-08                            Specification for Lap Cement Used with Asphalt Roll Roofing, Nonfibered, Asbestos Fibered and Nonasbestos Fibered.

D 3035-08                            Specification  for  Polyethylene  (PE)  Plastic  Pipe (DR-PR) Based On Controlled Outside Diameter

D 3161-09                            Test   Method   for   Wind   Resistance   of   Asphalt Shingles (Fan Induced Method)

D 3201-08ae1                      Test  Method  for  Hygroscopic  Properties  of  Fire-

retardant Wood and Wood-base Products

D 3309-96a (2002)               Specification  for  Polybutylene  (PB)  Plastic  Hot-

and Code-water Distribution System

D 3350-10                            Specification  for  Polyethylene  Plastic  Pipe  and Fitting Materials

D 3462/D 3462M-10a          Specification  for  Asphalt  Shingles  Made  From

Glass Felt and Surfaced with Mineral Granules.

D 3468-99 (2006)e01           Specification   for   Liquid-applied   Neoprene   and

Chlorosulfanated Polyethylene Used in Roofing and Waterproofing

D 3679-09a                          Specification   for   Rigid   Poly   (Vinyl   Chloride)

(PVC) Siding

D 3737-09                            Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)

D 3747-79 (2007)                 Specification for Emulsified Asphalt Adhesive for

Adhering Roof Insulation

D 3909-97b (2004)e01         Specification for Asphalt Roll Roofing (Glass Felt)

Surfaced with Mineral Granules

D 3957-09                            Standard  Practices  for  Establishing  Stress  Grades for Structural Members Used in Log Buildings

D 4022-07                            Specification for Coal Tar Roof Cement, Asbestos Containing

D 4318-10                            Test Methods for Liquid Limit, Plastic Limit and Plasticity Index of Soils

D 4434/D 4434-09               Specification   for   Poly   (Vinyl   Chloride)   Sheet

Roofing

D 4479-07                            Specification for Asphalt Roof Coatings-asbestos- free

D 4586-07                            Specification for Asphalt Roof Cement-asbestos- free

D 4601-04                            Specification for Asphalt-coated Glass Fiber Base Sheet Used in Roofing

D 4637/D 4637M-10            Specification for EPDM Sheet Used in Single-ply

Roof Membrane

D 4829-08a                          Test Method for Expansion Index of Soils

D 4869-05e01                      Specification  for  Asphalt-saturated  (Organic  Felt)

Underlayment Used in Steep Slope Roofing

D 4897/D 4897M-01(2009) Specification     for     Asphalt    Coated     Glass-fiber

Venting Base Sheet Used in Roofing

D 4990-97a (2005)e01         Specification  for  Coal  Tar  Glass  Felt  Used  in

Roofing and Waterproofing

D 5019-07a                          Specification      for      Reinforced     Nonvulcanized

Polymeric Sheet Used in Roofing Membrane

D 5055-10                            Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-joists

D 5516-09                            Test Method for Evaluating the Flexural Properties of Fire-retardant-treated Softwood Plywood Exposed to the Elevated Temperatures

D 5643-06                            Specification for Coal Tar Roof Cement Asbestos- free

D 5664-10                            Test Methods For Evaluating the Effects of Fire- retardant Treatments and Elevated Temperatures on Strength Properties of Fire-retardant-treated Lumber

D 5665-99a(2006)                Specification  for  Thermoplastic  Fabrics  Used  in

Cold-applied Roofing and Waterproofing

D 5726-98(2005)                  Specification  for  Thermoplastic  Fabrics  Used  in

Hot-applied Roofing and Waterproofing

D 6083-05e01                      Specification  for  Liquid-applied  Acrylic  Coating

Used in Roofing

D 6162-08                            Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements

D 6163-00 (2008)                 Specification for Styrene Butadiene Styrene (SBS)

Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements

D 6164-05e1                        Specification for Styrene Butadiene Styrene (SBS)

Modified Bituminous Sheet Materials Using Polyester Reinforcements

D 6222-08                            Specification for Atactic Polypropelene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcement.

D 6223/D 6223M-02(2009)e01        Specification    for    Atactic    Polypropelene

(APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcement

D 6298-05 e1                       Specification    for     Fiberglass-reinforced     Styrene

Butadiene Styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface

D 6305-08                            Practice for Calculating Bending Strength Design Adjustment Factors for Fire-retardant-treated Plywood Roof Sheathing

D 6380-03(2008)                  Standard  Specification  for  Asphalt  Roll  Roofing

(Organic Felt)

D 6694-08                            Standard Specification Liquid-applied Silicone Coating Used in Spray Polurethane Foam Roofing

D 6754/D 6754M-10            Standard Specification for Ketone-ethylene-ester- based Sheet Roofing2

D 6757-07                            Standard Specification for Inorganic Underlayment for Use with Steep Slope Roofing Products.

D 6841-08                            Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-retardant- treated Lumber

D 6878-08e1                        Standard      Specification         for       Thermoplastic-

polyolefin-based Sheet Roofing.

D 6947-07                                 Standard Specification for Liquid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System

D 7032-10a                          Standard Specification for Establishing Perfomance

Ratings for Wood-plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails).

D 7158-08d                          Standard  Test  Method  for  Wind  Resistance  of

Sealed Asphalt Shingles (Uplift Force/ Uplift Resistance Method

E 84-10b                               Test Method for Surface Burning Characteristics of Building Materials

E 90-04                                 Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements

E 96/E 96M-05                     Test  Method  for  Water  Vapor  Transmission  of

Materials

E 108-10a                             Test Methods for Fire Tests of Roof Coverings

E 119-10b                             Test Methods for Fire Tests of Building Construction and Materials

E 136-09b                             Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C

E 283-04                               Test Method for Determining the Rate of Air Leakage through Exterior Windows, Curtain Walls and Doors Under Specified Pressure Differences Across the Specimen

E 330-02 (2010)                   Test Method for Structural Performance of Exterior

Windows,  Curtain  Walls  and  Doors  by  Uniform Static Air Pressure Difference

E 331-00 (2009)                   Test  Method  for  Water  Penetration  of  Exterior

Windows, Skylights, Doors and Curtain Walls by Uniform Static Air Pressure Difference

E 492-09                               Specification for Laboratory Measurement of Impact Sound Transmission through Floor-ceiling Assemblies Using the Tapping Machine

E 814-10                               Test Method for Fire Tests of Through-penetration Firestops

E 970-10                               Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source

E 1509-04                             Standard Specification for Room Heaters, Pellet Fuel-burning Type

E 1602-03(2010)e1              Guide  for  Construction  of  Solid  Fuel  Burning

Masonry Heaters

E 1886-05                             Test Method for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Missles and Exposed to Cyclic Pressure Differentials

E 1996-09                             Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes

E 2178-03                                 Standard Test Method for Air Permeance of Building Materials

E 2231-09                             Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics

E 2273-03                             Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies

E 2568-09e1                         Standard  Specification  for  PB  Exterior  Insulation

and Finish Systems (EIFS)

E 2570-07                             Standard Test Methods for Evaluating Water- resistive Barrier (WRB) Coatings Used Under Exterior Insulation and Finish Systems (EIFS) or EIFS with Drainage

F 876-10                               Specification for Cross-linked Polyethylene (PEX) Tubing

F 877-07                               Specification for Cross-linked Polyethylene (PEX) Plastic Hot-and Cold-water Distribution Systems

F 1055-98(2006)                  Specification for Electrofusion Type Polyethylene

Fittings      for      Outside       Diameter      Controlled Polyethylene Pipe and Fittings

F 1281-07                             Specification                   for                    Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Pressure Pipe

F 1282-10                             Specification                                                           for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe

F 1554-07a                           Specification for Anchor Bolts, Steel, 36, 55 and 105-ksi Yield Strength

F 1667-10                             Specification for Driven Fasteners, Nails, Spikes and Staples

F 1807-10e1                         Specification for Metal Insert Fittings Utilizing a

Copper    Crimp     Ring    for     SDR9    Cross-linked Polyethylene (PEX) Tubing

F 1960-10                             Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing

F 1973-08                             Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA 11) Fuel Gas Distribution Systems

F 2090-10                             Specification for Window Fall Prevention Devices-with Emergency Escape (Egress) Release Mechanisms

F 2098-08                             Standard Specification for Stainless Steel Clamps for SDR9 PEX Tubing to Metal Insert Fittings

F 2389-10                             Standard  for  Pressure-rated  Polypropylene  (PP) Piping Systems

F 2623-08                             Standard Specification for Polyethylene of Raised Temperature (PE-RT) SDRG Tubing

American Wood Protection Association

P.O. Box 361784 Birmingham, AL 35236-1784

AWPA

Standard reference

number           Title

C1-03           All    Timber      Products-Preservative    Treatment    by    Pressure Processes

M4-06           Standard for the Care of Preservative-treated Wood Products U1-10            USE  CATEGORY  SYSTEM:  User  Specification  for  Treated

Wood Except Section 6 Commodity Specification H

Canadian General Standards Board

Place du Portage 111, 6B1 11 Laurier Street Gatineau, Quebec, Canada KIA 1G6

CGSB

Standard reference

number                                   Title

37-GP-52M-(1984)            Roofing    and    Waterproofing    Membrane,    Sheet Applied, Elastomeric

37-GP-56M-(1985)            Membrane, Modified Bituminous, Prefabricated and

Reinforced   for   Roofing-with   December   1985 Amendment

CAN/CGSB-37.54-95             Polyvinyl  Chloride   Roofing   and   Waterproofing

Membrane

Composite Panel Association 19465 Deerfield Avenue, Suite 306

Leesburg, VA 20176

CPA

Standard reference

number                                   Title

ANSI A135.4-04                 Basic Hardboard

ANSI A135.5-04                 Prefinished Hardboard Paneling ANSI A135.6-06                                            Hardboard Siding

Consumer Product Safety Commission 4330 East West Highway

Bethesda, MD 20814-4408

CPSC

Standard reference

number                                               Title

16 CFR Part 1201-(1977)                Safety Standard for Architectural Glazing

16 CFR Part 1209-(1979)                Interim    Safety    Standard    for    Cellulose

Insulation

16 CFR Part 1404-(1979)                Cellulose Insulation

Canadian Standards Association 5060 Spectrum Way

Mississauga, Ontario, Canada L4N 5N6

CSA

Standard reference

number                                   Title

CSA Requirement 3-88        Manually Operated Gas Valves for Use in House

Piping Systems

CSA 8-93                                Requirements for Gas Fired Log Lighters for Wood Burning Fireplaces-with Revisions through January 1999

O325-07                               Construction Sheathing

O437-Series-93                    Standards  on  OSB  and  Waferboard  (Reaffirmed

2006)

101/I.S.2/A440-08               Specifications    for    Windows,   Doors    and    Unit

Skylights

CAN/CSA B137.10M-09    Cross-linked  Polyethylene/Aluminum/Polyethylene

Composite Pressure Pipe Systems

Cedar Shake & Shingle Bureau

P. O. Box 1178

Sumas, WA 98295-1178

CSSB

Standard reference

number                       Title

CSSB-97                       Grading and Packing Rules for Western Red Cedar Shakes and Western Red Shingles of the Cedar Shake and Shingle Bureau

Door and Access Systems Manufacturers Association International 1300 Summer Avenue

Cleveland, OH 44115-2851

DASMA

Standard reference

number                       Title

108-05                      Standard Method for Testing Garage Doors: Determination of Structural Performance Under Uniform Static Air Pressure Difference

United States Department of Commerce 1401 Constitution Avenue, NW Washington, DC 20230

DOC

Standard reference

number                                   Title

PS 1-07                                 Structural Plywood

PS 2-04                                 Performance Standard for Wood-based Structural- use Panels

R803.2.1/ PS 20-05              American Softwood Lumber Standard

Department of Transportation

1200 New Jersey Avenue SE East Building, 2nd floor Washington, DC 20590

DOTn

Standard reference

number                                               Title

49 CFR, Parts 192.281(e) &

192.283 (b)                                          Transportation of Natural and Other Gas by Pipeline: Minimum Federal Safety Standards

Federal Emergency Management Agency 500 C Street, SW

Washington, DC 20472

FEMA

Standard reference

number                       Title

TB-2-08                    Flood Damage-Resistant Materials Requirements

FIA-TB-11-01             Crawlspace Construction for Buildings Located in Special Flood Hazard Area

Factory Mutual Global Research Standards Laboratories Department 1301 Atwood Avenue, P. O. Box 7500 Johnson, RI 02919

FM

Standard reference

number                       Title

4450-(1989)              Approval  Standard  for  Class  1  Insulated  Steel  Deck Roofs-with Supplements through July 1992

4880-(2010)              American National Standard for Evaluating Insulated Wall or Wall and Roof/Ceiling Assemblies, Plastic Interior Finish Materials, Plastic Exterior Building Panels, Wall/Ceiling Coating Systems, Interior or Exterior Finish Systems

Gypsum Association

810 First Street, Northeast, Suite 510

Washington, DC 20002-4268

GA

Standard reference

number                       Title

GA-253-07               Application of Gypsum Sheathing

Hardwood Plywood & Veneer Association 1825 Michael Faraday Drive

Reston, Virginia 20190-5350

HPVA

Standard reference

number                       Title

HP-1-2009                The   American   National   Standard   for   Hardwood   and Decorative Plywood

International Code Council, Inc.

500 New Jersey Avenue, NW 6th Floor Washington, DC 20001

ICC

Standard reference

number                                   Title

ICC/ANSI A117.1 - 09          Accessible and Usable Buildings and Facilities

ICC 400 - 07                           Standard on the Design and Construction of Log Structures

ICC 500 - 08                           ICC/NSSA     Standard       on      the     Design       and Construction of Storm Shelters

ICC 600 - 08                           Standard for Residential Construction in High Wind Regions

IEBC-09                                 International Existing Buildings Code

IECC - 09                               International Energy Conservation Code (adoption includes only section 101 of chapter 1 and chapters 2 through 6)

IFGC - 09                               International    Fuel     Gas     Code    (including       ICC Emergency Amendment changing section 406.7)

International Organization for Standardization

1, ch. de la Voie -Creuse Case postale 56 CH-1211 Geneva 20, Switzerland

ISO

Standard reference

number                       Title

15874-03                  Polypropylene  Plastic Piping Systems for Hot and Cold Water Installations

Manufacturers Standardization Society of the Valve and Fittings Industry 127 Park Street, Northeast

Vienna, VA 22180

MSS

Standard reference

number                       Title

SP-58-09                  Pipe    Hangers    and    Supports-Materials,    Design     and Manufacture

North American Insulation Manufacturers Association 44 Canal Center Plaza, Suite 310

Alexandria, VA 22314

NAIMA

Standard reference

number                       Title

AH 116-02               Fibrous Glass Duct Construction Standards, Fifth Edition

National Concrete Masonry Association 13750 Sunrise Valley Drive

Herndon, VA 20171-4662

NCMA

Standard

reference

number                       Title

TR 68-A-75              Design and Construction of Plain and Reinforced Concrete Masonry and Basement and Foundation Walls

National Fire Protection Association 1 Batterymarch Park

Quincy, MA 02269

NFPA

Standard reference

number                       Title

13-10                        Installation of Sprinkler Systems (including TIA 10-2)

13D-10                     Standard for the Installation of Sprinkler Systems in One- and Two-family Dwellings and Manufactured Homes (including TIA 10-2)

13R-10                        Standard for the Installation of Sprinkler Systems in Residential Occupancies up to and Including Four Stories in Height (including TIA 10-2)

31-06                        Installation of Oil-burning Equipment

58-11                        Liquefied Petroleum Gas Code

70-11                        National Electrical Code (including TIA 11-1)

72-10                        National Fire Alarm Code

85-07                        Boiler and Construction Systems Hazards Code

211-10                      Chimneys,  Fireplaces,  Vents  and  Solid  Fuel  Burning Appliances

259-08                      Test Method for Potential Heat of Building Materials 286-06                                                Standard Methods of Fire Tests for Evaluating Contribution

of Wall and Ceiling Interior Finish to Room Fire Growth

501-05                      Standard on Manufactured Housing

853-10                      Standard for the Installation of Stationary Fuel Cell Power Systems

National Fenestration Rating Council Inc. 8484 Georgia Avenue, Suite 320

Silver Spring, MD 20910

NFRC

Standard reference

number                       Title

100-10                      Procedure for Determining Fenestration Product U-factors 200-10                                    Procedure for Determining Fenestration Product Solar Heat

Gain  Coefficients  and  Visible  Transmittance  at  Normal Incidence

400-10                      Procedure    for    Determining    Fenestration    Product   Air Leakage

Portland Cement Association 5420 Old Orchard Road Skokie, IL 60077

PCA

Standard reference

number                       Title

100-07                      Prescriptive Design of Exterior Concrete Walls for One- and Two-family Dwellings (Pub. No. EB241)

Sheet Metal & Air Conditioning Contractors National Assoc. Inc. 4021 Lafayette Center Road

Chantilly, VA 22021

SMACNA

Standard reference

number                       Title

SMACNA-03             Fibrous Glass Duct Construction Standards (2003)

The Masonry Society

3970 Broadway, Suite 201-D Boulder, CO 80304

TMS

Standard reference

number                       Title

302-07                      Standard Method for Determining the Sound Transmission Class Rating for Masonry Walls

402-08                      Building Code Requirements for Masonry Structures 602-08                                    Specification for Masonry Structures

Truss Plate Institute

583 D'Onofrio Drive, Suite 200

Madison, WI 53719

TPI

Standard reference

number                       Title

TPI 1-2007               National Design Standard for Metal-plate-connected Wood Truss Construction

Underwriters Laboratories, Inc. 333 Pfingsten Road

Northbrook, IL 60062

UL

Standard reference

number                       Title

17-08                        Vent    or    Chimney     Connector      Dampers     for   Oil-fired Appliances

58-96                             Steel Underground Tanks for Flammable and Combustible Liquids-with Revisions through July 1998

80-07                        Steel Tanks for Oil-burner Fuel

103-10                      Factory-built Chimneys for Residential Type and Building Heating Appliances

127-08                      Factory-built Fireplaces

174-04                           Household  Electric  Storage  Tank  Water  Heaters-with Revisions through November 2005

181-05                      Factory-made Air Ducts and Air Connectors

181A-05                        Closure  Systems  for  Use  with  Rigid  Air  Ducts  and  Air Connectors

181B-05                        Closure Systems for Use with Flexible Air Ducts and Air Connectors

217-06                      Single- and Multiple-station Smoke Alarms

263-03                           Standards  for  Fire  Test  of  Building  Construction  and Materials

325-02                      Standard for Door, Drapery, Gate, Louver and Window Operations and Systems-with Revisions through February 2006

343-08                      Pumps for Oil-burning Appliances

441-10                      Gas Vents

508-99                      Industrial  Control  Equipment-with  Revisions  through July 2005

536-97                      Flexible Metallic Hose-with Revisions through June 2003 641-95   Type                                    L,          Low-temperature                 Venting      Systems-with

Revisions through August 2005

651-05                      Schedule  40  and  Schedule  80  Rigid  PVC  Conduit  and Fittings

723-08                      Standard for Test for Surface Burning Characteristics of Building Materials

726-95                      Oil-fired    Boiler    Assemblies-with    Revisions      through March 2006

727-06                      Oil-fired Central Furnaces

729-03                      Oil-fired Floor Furnaces

730-03                      Oil-fired Wall Furnaces

732-95                      Oil-fired Storage Tank Water Heaters

737-07                      Fireplaces Stoves

790-04                      Standard Test Methods for Fire Tests of Roof Coverings 795-06                                    Commercial-industrial Gas Heating Equipment.

834-04                      Heating, Water Supply and Power Boilers-Electric 896-93     Oil-burning Stoves-with Revisions through May 2004 923-08     Microwave Cooking Appliances

959-01                      Medium  Heat  Appliance  Factory-built  Chimneys-with Revisions through September 2006

1040-96                    Fire Test of Insulated Wall Construction-with Revisions through June 2001

1256-02                    Fire Test of Roof Deck Construction.

1261-01                    Electric Water Heaters for Pools and Tubs-with Revisions through June 2004

1453-04                    Electronic Booster and Commercial Storage Tank Water Heaters

1479-03                    Fire Tests of Through-penetration Firestops 1482-10   Solid-fuel-type Room Heaters

1715-97                    Fire  Test  of  Interior  Finish  Material-with  Revisions through March 2004

1738-10                    Venting Systems for Gas-burning Appliances, Categories II, III and IV

1777-07                    Standard for Chimney Liners

1995-05                    Heating and Cooling Equipment.

2017-08                    Standard   for   General-purpose   Signaling   Devices   and Systems-with Revisions through June 2004

2034-08                    Standard    for     Single-     and     Multiple-station     Carbon Monoxide Alarms.

2158A-10                 Outline of Investigation for Clothes Dryer Transition Duct

Underwriters' Laboratories of Canada 7 Underwriters Road Toronto, Ontario, Canada M1R 3B4

ULC

Standard reference

number                                   Title

CAN/ULC S 102-10            Standard  Methods  for  Test  for  Surface  Burning

Characteristics      of      Building      Materials      and Assemblies

United States - Federal Trade Commission 600 Pennsylvania Avenue NW Washington, DC 20580

US-FTC

Standard reference

number                                   Title

CFR Title 16 Part 460             R-value Rule

Window & Door Manufacturers Association 1400 East Touhy Avenue, Suite 470

Des Plaines, IL 60018

WDMA

Standard reference

number                                   Title

AAMA/WDMA/CSA

101/I.S2/A440-08                Specifications for Windows, Doors and Skylights

Replaces:                                                     4101:8-43-01.1, 4101:8-43-01.2

Effective:                                                     01/01/2013

R.C. 119.032 review dates:                         01/01/2018

CERTIFIED ELECTRONICALLY

Certification

05/29/2012

Date

Promulgated Under:                           119.03

Statutory Authority:                           3781.10(A) , 4104.43(A)(1)

Rule Amplifies:                                  3781.01, 3781.06, 3781.10, 3781.11, 3791.04, 4740.14

Prior Effective Dates:                         5/27/06, 1/1/08, 3/31/08 (Emerg.), 6/24/08, 1/1/09