4101:3-13-01 Referenced standards.

 

 

 

 

 

 

4101:3-13-01 Referenced standards.

 

                                                                          General. This chapter lists the codes and standards that are referenced in various sections of the plumbing code. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and the title. The application of the referenced standards shall be as specified in Section 102.4 of the building code.

 

                                                                          Referenced codes. When indicated in this code, the following codes refer to provisions in the listed chapters of the Administrative Code:

 

Referenced code	Ohio Administrative Code chapters
Building Code	4101:1-1 to 4101:1-35
Fire Code	1301:7-1 to 1301:7-7
Mechanical Code	4101:2-1 to 4101:2-15
Ohio Boiler and Pressure Vessel Rules	4101:4-1 to 4101:4-10

 

                        Referenced Standards.

 

American National Standards Institute 25 West 43rd Street, Fourth Floor New York, NY 10036

 

ANSI

Standard Reference

Number                      Title

Z4.3-95                             Minimum Requirements for Nonsewered Waste-Disposal Systems- (Standard is developed by the Portable Sanitation Association International-PSAI)

Z21.22-99 (R2003)         Relief Valves for Hot Water Supply Systems with Addenda Z21.22a-2000(R2003) and Z21.22b-2001(R2003)-

(Standard is developed by the Canadian Standards Association-CSA and is the same as CSA 4.4-M99)

Z124.1.2- 05                Plastic Bathtub and Shower Units (Standard is developed by IAPMO)

Z124.3- 05                   Plastic Lavatories (Standard is developed by IAPMO)

Z124.4-96                     Plastic Water Closet Bowls and Tanks(Standard is

developed by IAPMO)

Z124.6-97                     Plastic Sinks (Standard is developed by IAPMO)

Z124.9- 04                   Plastic Urinal Fixtures (Standard is developed by IAPMO)

 

 

 

 

 

 

 

 

Air-Conditioning & Refrigeration Institute 4100 North Fairfax Drive, Suite 200

Arlington, VA 22203

ARI

Standard reference

number           Title

1010-02           Self-contained, Mechanically Refrigerated Drinking-water Coolers

American Society of Mechanical Engineers Three Park Avenue

New York, NY 10016-5990

ASME

Standard reference

number                                   Title

A112.1.2-2004                        Air Gaps in Plumbing Systems

A112.1.3-2000                        Air Gap Fittings for Use with Plumbing Fixtures,

Appliances and Appurtenances

A112.3.1-1993                        Performance Standard and Installation Procedures

for Stainless Steel Drainage Systems for Sanitary, Storm and Chemical Applications, Above and Below Ground

A112.3.4-2000(R2004)           Macerating Toilet Systems and Related

Components

A112.4.1-1993(R2002)           Water Heater Relief Valve Drain Tubes A112.4.3-1999(R2004)                                                Plastic Fittings for Connecting Water Closets to

the Sanitary Drainage System A112.6.1M-1997(R2002)                                                Floor-Affixed Supports for Off-the-floor

Plumbing Fixtures for Public Use

A112.6.2-2000(R2004)           Framing-Affixed Supports for Off-the-floor

Water Closets with Concealed Tanks

A112.6.3-2001                        Floor and Trench Drains

A112.6.7-2001                        Enameled and Epoxy-coated Cast-iron and PVC

Plastic Sanitary Floor Sinks

A112.14.1-2003                      Backwater Valves A112.14.3-2000(R2004)                                                Grease Interceptors A112.14.4-2001                                                Grease Removal Devices

A112.18.1- 2005                     Plumbing Fixture Fittings

A112.18.2- 2005                     Plumbing Fixture Waste Fittings A112.18.3-2002                                                Performance Requirements for Backflow

Protection Devices and Systems in Plumbing Fixture Fittings

A112.18.6-2003                      Flexible Water Connectors

A112.18.7-1999 (R2004)        Deck mounted Bath/Shower Transfer Valves with

Integral Backflow Protection

A112.19.1M-1994(R2004)     Enameled Cast Iron Plumbing Fixtures with 1998

and 2000 supplements

A112.19.2M-2003                  Vitreous China Plumbing Fixtures and Hydraulic

Requirements for Water Closets and Urinals A112.19.3-2000(R2004)                           Stainless Steel Plumbing Fixtures (Designed for

Residential Use) with 2002 Supplement A112.19.4M-1994(R2004)                           Porcelain Enameled Formed Steel Plumbing

Fixtures with 1998 and 2000 Supplement A112.19.5-1999                                                Trim for Water-closet Bowls, Tanks and Urinals A112.19.6-1995                                                Hydraulic Performance Requirements for Water

Closets and Urinals A112.19.7M-1995                                                Whirlpool Bathtub Appliances

A112.19.8M-1987(R1996)     Suction Fittings for Use in Swimming Pools,

Wading Pools, Spas, Hot Tubs and Whirlpool Bathtub Appliances

A112.19.9M-1991(R2002)     Non-Vitreous Ceramic Plumbing Fixtures with 2002 Supplement

A112.19.12-2000(R2004)       Wall Mounted and Pedestal Mounted, Adjustable

and Pivoting Lavatory and       Sink Carrier Systems

A112.19.13-2001                    Electrohydraulic Water Closets

A112.19.15-2005                    Bathtub/Whirlpool Bathtubs with Pressure Sealed

Doors

A112.21. 2M-1983                 Roof Drains A112.36. 2M-1991(R2002)                           Cleanouts

B1.20.1-1983(R2001)             Pipe Threads, General Purpose (inch)

B16.3-1998                             Malleable Iron Threaded Fittings Classes 150 and 300

B16.4-1998                             Gray Iron Threaded Fittings Classes 125 and 250

B16.9-2003                             Factory-made Wrought Steel Buttwelding Fittings

B16.11-2001                           Forged Fittings, Socket-welding and Threaded

B16.12-1998                           Cast-iron Threaded Drainage Fittings B16.15-1985(R2004)                           Cast Bronze Threaded Fittings

B16.18-2001                           Cast Copper Alloy Solder Joint Pressure Fittings

B16.22-2001                                Wrought Copper and Copper Alloy Solder Joint Pressure Fittings

B16.23-2002                           Cast Copper Alloy Solder Joint Drainage Fittings DWV

B16.26-1988                           Cast Copper Alloy Fittings for Flared Copper Tubes

B16.28-1994                           Wrought Steel Buttwelding Short Radius Elbows and Returns

B16.29-2001                           Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings (DWV)

BPVC Section IX-2004           Welding and Brazing Qualifications.

American Society of Sanitary Engineering 901 Canterbury Road, Suite A

Westlake, OH 44145

ASSE

Standard reference

number           Title

1001-02           Performance Requirements for Atmospheric Type Vacuum Breakers

1002-99           Performance Requirements for Antisiphon Fill Valves (Ballcocks) for Gravity Water Closet Flush Tanks

1003-01           Performance Requirements for Water Pressure Reducing Valves 1004-90                        Performance Requirements for Backflow Prevention Requirements

for Commercial Dishwashing Machines

1005-99           Performance Requirements for Water Heater Drain Valves 1006- 86                        Performance Requirements for Residential Use Dishwashers 1007- 86                        Performance Requirements for Home Laundry Equipment

1008- 86          Performance Requirements for Household Food Waste Disposer Units

1009-90           Performance Requirements for Commercial Food Waste Grinder Units

1010-04           Performance Requirements for Water Hammer Arresters

1011- 04          Performance Requirements for Hose Connection Vacuum Breakers 1012-02                        Performance Requirements for Backflow Preventers with

Intermediate Atmospheric Vent

1013- 05 Performance Requirements for Reduced Pressure Principle Backflow Preventers and Reduced Pressure Fire Protection Principle Backflow Preventers

1014- 05          Performance Requirements for Handheld Showers

1015- 05          Performance Requirements for Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies

1016-05           Performance Requirements for Individual Thermostatic, Pressure Balancing and Combination Control Valves for Individual Fixture Fittings

1017- 03          Performance Requirements for Temperature Actuated Mixing Valves for Hot Water Distribution Systems

1018-01           Performance Requirements for Trap Seal Primer Valves; Potable Water Supplied

1019- 04          Performance Requirements for Vacuum Breaker Wall Hydrants, Freeze Resistant, Automatic Draining Type

1020- 04          Performance Requirements for Pressure Vacuum Breaker Assembly

1022-03           Performance Requirements for Backflow Preventer for Carbonated Beverage Machines

1024-04                Performance Requirements for Dual Check Valve Type Backflow Preventers

(for Residential Supply Service or Individual Outlets)

1035-02           Performance Requirements for Laboratory Faucet Backflow Preventers

1037-90                Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures

1044-01                Performance Requirements for Trap Seal Primer Devices Drainage Types and Electronic Design Types

1047- 05          Performance Requirements for Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies

1048- 05          Performance Requirements for Double Check Detector Fire Protection Backflow Prevention Assemblies 7

1050-02                Performance Requirements for Stack Air Admittance Valves for Sanitary Drainage Systems

1051-02                Performance Requirements for Individual and Branch Type Air Admittance Valves for Sanitary Drainage Systems Fixture and Branch Devices

1052-04           Performance Requirements for Hose Connection Backflow Preventers

1055-97           Performance Requirements for Chemical Dispensing Systems 1056-01 Performance Requirements for Spill Resistant Vacuum Breaker 1060- 06      Performance Requirements for Outdoor Enclosures for Backflow

Prevention Assemblies

1062-97           Performance Requirements for Temperature Actuated, Flow

Reduction Valves to Individual Fixture Fittings

1066-97           Performance Requirements for Individual Pressure Balancing In- line Valves for Individual Fixture Fittings

1069-05           Performance Requirements for Automatic Temperature Control Mixing Valves

1070-04           Performance Requirements for Water-temperature Limiting Devices

5013-98           Performance Requirements for Testing Reduced Pressure Principle Backflow Prevention Assembly (RPA) and Reduced Pressure Fire Protection Principle Backflow Preventers (RFP)

5015-98           Performance Requirements for Testing Double Check Valve Backflow Prevention Assembly (DCVA)

5020-98           Performance Requirements for Testing Pressure Vacuum Breaker Assembly (PVBA)

5047-98           Performance Requirements for Testing Reduced Pressure Detector Fire Protection

Backflow Prevention Assemblies (RPDA)

5048-98           Performance Requirements for Testing Double Check Valve Detector Assembly (DCDA)

5052-98                Performance Requirements for Testing Hose Connection Backflow Preventers

5056-98                Performance Requirements for Testing Spill Resistant Vacuum Breaker

ASTM International 100 Barr Harbor Drive

West Conshohocken, PA 19428-2959

ASTM

Standard Reference

Number                      Title

A 53/A 53M- 04a       Specification for Pipe, Steel, Black and Hot-dipped, Zinc- coated Welded and Seamless

A 74-04a                     Specification for Cast-iron Soil Pipe and Fittings

A 312/A 312M-05           Specification for Seamless and Welded Austenitic Stainless Steel Pipes

A 733-03                          Specification for Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples

A 778-01                          Specification for Welded Unannealed Austenitic Stainless Steel Tubular Products

A 888-04a                   Specification for Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Application

B 32-04                       Specification for Solder Metal

B 42-02?1                           Specification for Seamless Copper Pipe, Standard Sizes

B 43-98(2004)            Specification for Seamless Red Brass Pipe, Standard Sizes B 75-02                                         Specification for Seamless Copper Tube

B 88-03                       Specification for Seamless Copper Water Tube

B 152/B 152M-00       Specification for Copper Sheet, Strip Plate and Rolled Bar B 251-02 ?1                                                Specification for General Requirements for Wrought

Seamless Copper and Copper-alloy Tube

B 302-02                     Specification for Threadless Copper Pipe, Standard Sizes B 306-02                                    Specification for Copper Drainage Tube (DWV)

B 447-02                     Specification for Welded Copper Tube

B 687-99                     Specification for Brass, Copper and Chromium-plated Pipe Nipples

B 813-00 ?1                       Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube

B 828-02                     Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings

C 4- 04                        Specification for Clay Drain Tile and Perforated Clay Drain Tile

C 14-03                            Specification for Concrete Sewer, Storm Drain and Culvert Pipe

C 76-04a                          Specification for Reinforced Concrete Culvert, Storm Drain and Sewer Pipe

C 296-00(2004)?1          Specification for Asbestos-cement Pressure Pipe

C 425-04                     Specification for Compression Joints for Vitrified Clay Pipe and Fittings

C 428-97(2002) ?1         Specification for Asbestos-cement Nonpressure Sewer Pipe C 443- 05                                    Specification for Joints for Concrete Pipe and Manholes,

Using Rubber Gaskets

C 508-00(2004)           Specification for Asbestos-cement Underdrain Pipe

C 564-03a                    Specification for Rubber Gaskets for Cast-iron Soil Pipe and Fittings

C 700-02                     Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated

C 1053-00                   Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste, andVent (DWV) Applications

C 1173-02                   Specification for Flexible Transition Couplings for Underground Piping System

C 1277-04                   Specification for Shielded Coupling Joining Hubless Cast- iron Soil Pipe and Fittings

C 1440- 03                  Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste, and Vent (DWV), Sewer, Sanitary and Storm Plumbing Systems

C 1460-04                   Specification for Shielded Transition Couplings for Use with Dissimilar DWV Pipe and Fittings Above Ground

C 1461-02                   Specification for Mechanical Couplings Using

Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste and Vent (DWV) Sewer, Sanitary and Storm Plumbing Systems for Above and Below Ground Use

C 1540-02                   Specification for Heavy Duty Shielded Couplings Joining Hubless Cast-iron Soil Pipe and Fittings

C 1563-04                   Standard Test Method for Gaskets for Use in Connection with Hub and Spigot Cast Iron Soil Pipe and Fittings for Sanitary Drain, Waste, Vent and Storm Piping Applications

D 1527-99 ?1                    Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80

D 1785-04a                 Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80 and 120

D 1869-95(2000)        Specification for Rubber Rings for Asbestos-cement Pip D 2235-04                                    Specification for Solvent Cement for Acrylonitrile-

Butadiene-Styrene (ABS) Plastic Pipe and Fittings

D 2239-03                        Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

D 2241-04b                 Specification for Poly (Vinyl Chloride) (PVC) Pressure- rated Pipe (SDR-Series)

D 2282-99 ?1                    Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR)

D 2464-99 ?1                    Specification for Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

D 2466-02                   Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40

D 2467-04 ?1                    Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

D 2468-96a                 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 40

D 2564- 04                  Specification for Solvent Cements for Poly (Vinyl

Chloride) (PVC) Plastic Piping Systems

D 2609-02                   Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe

D 2657- 03                  Standard Practice for Heat Fusion-joining of Polyolefin Pipe and Fitting

D 2661-02                   Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

D 2662-96a                 Specification for Polybutylene (PB) Plastic Pipe (SDR-PR) Based on Controlled Inside Diameter

D 2665-04a ?1                   Specification for Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

D 2666-96a                 Specification for Polybutylene (PB) Plastic Tubing

D 2672-96a(2003)       Specification for Joints for IPS PVC Pipe Using Solvent Cement

D 2729- 03                  Specification for Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

D 2737-03                   Specification for Polyethylene (PE) Plastic Tubing

D 2751-96a                 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings

D 2846/D 2846M-99 ?1 Specification for Chlorinated Poly (Vinyl Chloride)

(CPVC) Plastic Hot and Cold Water Distribution Systems

D 2855-96(2002)        Standard Practice for Making Solvent-cemented Joints with Poly (Vinyl Chloride) (PVC) Pipe and Fittings

D 2949-01a ?1                   Specification for 3.25-in Outside Diameter Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

D 3034-04a                 Specification for Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

D 3139-98 (2005)       Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals

D 3212-96a(2003) ?1    Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

D 3309-96a(2002)       Specification for Polybutylene (PB) Plastic Hot and Cold Water Distribution Systems

D 3311-02 ?1                    Specification for Drain, Waste and Vent (DWV) Plastic Fittings Patterns

D 4068-01                   Specification for Chlorinated Polyethlene (CPE) Sheeting for Concealed Water-Containment Membrane

D 4551-96(2001)        Specification for Poly (Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane

F 405-97                      Specification for Corrugated Polyethylene (PE) Tubing and Fittings

F 409-02                      Specification for Thermoplastic Accessible and

Replaceable Plastic Tube and Tubular Fittings

F 437-99                      Specification for Threaded Chlorinated Poly (Vinyl

Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 F 438-04                                    Specification for Socket-type Chlorinated Poly (Vinyl

Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40 F 439-02 ?1                                                Specification for Socket-type Chlorinated Poly (Vinyl

Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 F 441/F 441M-02                                    Specification for Chlorinated Poly (Vinyl Chloride)

(CPVC) Plastic Pipe, Schedules 40 and 80

F 442/F 442M-99        Specification for Chlorinated Poly (Vinyl Chloride)

(CPVC) Plastic Pipe (SDR-PR)

F 477-02 ?1                        Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

F 493-04                      Specification for Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

F 628-01                      Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe with a Cellular Core

F 656-02                      Specification for Primers for Use in Solvent Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings

F 714-03                      Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Outside Diameter

F 876-04                      Specification for Cross-linked Polyethylene (PEX) Tubing F 877- 05                                    Specification for Cross-linked Polyethylene (PEX) Plastic

Hot and Cold Water Distribution Systems

F 891- 04                     Specification for Coextruded Poly (Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core

F 1281-03                    Specification for Cross-linked Polyethylene/Aluminum/Cross-Linked Polyethylene (PEX- AL-PEX) Pressure Pipe

F 1282-03                    Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe

F 1412-01 ?1                     Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage

F 1488-03                    Specification for Coextruded Composite Pipe

F 1807-04                    Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing

F 1866-98                    Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings

F 1960-04a                  Specification for Cold Expansion Fittings with PEX

Reinforcing Rings for use with Cross-linked Polyethylene (PEX) Tubing

F 1974-04                    Specification for Metal Insert Fittings for

Polyethylene/Aluminum/Polyethylene and Cross-linked Polyethylene/Aluminum/Cross-linked    Polyethylene Composite Pressure Pipe

F 1986-00a                  Specification for Multilayer Pipe, Type 2, Compression Fittings and Compression Joints for Hot and Cold Drinking Water Systems

F 2080-04                    Specifications for Cold-expansion Fittings with Metal Compression-sleeves for Cross-linked Polyethylene (PEX) Pipe

F 2159-03                    Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing

F 2389-04                    Specification for Pressure-rated Polypropylene (PP) Piping Systems

American Welding Society 550 N.W. LeJeune Road Miami, FL 33126

AWS

Standard Reference Number   Title

A5.8-04           Specifications for Filler Metals for Brazing and Braze Welding

American Water Works Association 6666 West Quincy Avenue

Denver, CO 80235

AWWA

Standard Reference

Number                      Title

C104/A21.4-03           Standard for Cement-mortar Lining for Ductile-Iron Pipe and Fittings for Water

C110/A21.10-03         Standard for Ductile-iron and Gray-iron Fittings, 3 Inches through 48 Inches, for Water

C111/A21.11-00              Standard for Rubber-gasket Joints for Ductile-iron Pressure Pipe and Fittings

C115/A21.15-05         Standard for Flanged Ductile-iron Pipe with Ductile-iron or Gray-iron Threaded Flanges

C151/A21.51-02         Standard for Ductile-iron Pipe, Centrifugally Cast for Water

C153/A21.53-00              Standard for Ductile-iron Compact Fittings for Water Service

C510-97                      Double Check Valve Backflow Prevention Assembly

C511-97                      Reduced-pressure Principle Backflow Prevention Assembly C651-05                                    Disinfecting Water Mains

C652-02                      Disinfection of Water-storage Facilities

Cast Iron Soil Pipe Institute

5959 Shallowford Road, Suite 419

Chattanooga, TN 37421

CISPI

Standard Reference Number   Title

301-05             Specification for Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

310-04             Specification for Coupling for Use in Connection with Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

Canadian Standards Association 178 Rexdale Blvd.

Rexdale (Toronto), Ontario, Canada M9W 1R3

CSA

Standard Reference

Number                                  Title

A257.1M-03                               Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

A257.2M-03                           Reinforced Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

A257.3M-03                               Joints for Circular Concrete Sewer and Culvert Pipe, Manhole Sections and Fittings Using Rubber

Gaskets

B45.1-02                     Ceramic Plumbing Fixtures

B45.2-02                     Enameled Cast-iron Plumbing Fixtures B45.3-02                                    Porcelain Enameled Steel Plumbing Fixtures B45.4-02                                    Stainless-steel Plumbing Fixtures

B45.5-02                     Plastic Plumbing Fixtures

B45.9-99                     Macerating Systems and Related Components B45.10-01                                    Hydromassage Bathtubs

B64.1.1-01                  Vacuum Breakers, Atmospheric Type (AVB) B64.1.2-01(R2006)                   Vacuum Breakers, Pressure Type (PVB)

B64.2-01                     Vacuum Breakers, Hose Connection Type (HCVB) B64.2.1-01 Vacuum Breakers, Hose Connection Type (HCVB) with

Manual Draining Feature

B64.2.1.1-01               Vacuum Breakers, Hose Connection Dual Check Type (HCDVB)

B64.2.2-01                  Vacuum Breakers, Hose Connection Type (HCVB) with Automatic Draining Feature

B64.3-01                     Backflow Preventers, Dual Check Valve Type with

Atmospheric Port (DCAP)

B64.3.1-01                  Backflow Preventers, Dual Check Valve Type with

Atmospheric Port for Carbonators (DCAPC)

B64.4-01                     Backflow Preventers, Reduced Pressure Principle Type (RP)

B64.4.1-01                  Backflow Preventers, Reduced Pressure Principle Type for Fire Sprinklers (RPF)

B64.5-01                     Backflow Preventers, Double Check Type (DCVA)

B64.5.1-01                  Backflow Preventers, Double Check Type for Fire Systems (DCVAF)

B64.6-01                     Backflow Preventers, Dual Check Valve Type (DuC) B64.7-94                                               Vacuum Breakers, Laboratory Faucet Type (LFVB) B64.10-01 Manual for the Selection and Installation of Backflow

Prevention Devices

B64.10.1-01                     Manual for the Maintenance and Field Testing of Backflow Prevention Devices

B79-05                        Floor, Area and Shower Drains, and Cleanouts for Residential Construction

B125.3-05                   Plumbing Fittings

B137.1-05                   Polyethylene Pipe, Tubing and Fittings for Cold Water Pressure Services

B137.2-05                   PVC Injection-moulded Gasketed Fittings for Pressure Applications

B137.3-05                   Rigid Poly (Vinyl Chloride) (PVC) Pipe for Pressure Applications

B137.5-05                   Cross-linked Polyethylene (PEX) Tubing Systems for Pressure Applications

B137.6-05                   CPVC Pipe, Tubing and Fittings for Hot and Cold Water Distribution Systems

B137.8M-05              Polybutylene (PB) Piping for Pressure Applications B137.9-05                                      Polyethylene/Aluminum/Polyethylene Composite Pressure

Pipe Systems

B137.10M-05             Cross-linked    Polyethylene/Aluminum/Polyethylene

Composite Pressure Pipe Systems

B137.11-05                 Polypropylene (PP-R) Pipe and Fittings for Pressure

Applications

B181.1-02(S1-05) ABS Drain, Waste and Vent Pipe and Pipe Fittings B181.2-02(S1-05) PVC Drain, Waste, and Vent Pipe and Pipe Fittings B181.3-02(S1-05)      Polyolefin Laboratory Drainage Systems

B182.1-02(S1-05)       Plastic Drain and Sewer Pipe and Pipe Fittings B182.2-02(S1-05)                                    PVC Sewer Pipe and Fittings (PSM Type) B182.4-02(S1-05)                                    Profile PVC Sewer Pipe and Fittings

B182.6-02(S1-05)       Profile Polyethylene Sewer Pipe and Fittings for Leak- proof Sewer Applications

B182.8-02(S1-05)    Profile Polyethylene Storm Sewer and Drainage Pipe and Fittings

B602-05                       Mechanical Couplings for Drain, Waste and Vent Pipe and Sewer Pipe

Federal Emergency Management Agency Federal Center Plaza

500 C Street S.W. Washington, DC 20472

FEMA

Standard reference

number                                   Title

44 CFR parts 59-77

International Code Council 5203 Leesburg Pike, Suite 600 Falls Church, VA 22041

ICC

Standard Reference

Number                      Title

IFGC-06                     International Fuel Gas Code® Industry Safety Equipment Association

1901 N. Moore Street, Suite 808

Arlington, VA 22209

ISEA

Standard Reference

Number                      Title

Z358.1-04                     Emergency Eyewash and Shower Equipment

National Fire Protection Association Batterymarch Park

Quincy, MA 02269

NFPA

Standard Reference Number   Title

70-05               National Electrical Code (including TIA 05-2) (This edition is applicable only for one-, two-, and three-family dwellings)

70-08               National Electrical Code 99C-05 Gas and Vacuum Systems

NSF International 789 Dixboro Road Ann Arbor, MI 48105

NSF

Standard Reference Number   Title

3-05                 Commercial Warewashing Equipment

14-03               Plastic Piping System Components and Related Materials 18- 05                        Manual Food and Beverage Dispensing Equipment

42-05e               Drinking Water Treatment Units-Aesthetic Effects 44-04                        Residential Cation Exchange Water Softeners

53-06               Drinking Water Treatment Units-Health Effects

58- 06a1      Reverse Osmosis Drinking Water Treatment Systems 61- 05a1 Drinking Water System Components-Health Effects 62-04a1     Drinking Water Distillation Systems

Plumbing and Drainage Institute 800 Turnpike Street, Suite 300 North Andover, MA 01845

PDI

Standard Reference Number   Title

G101(2003)       Testing and Rating Procedure for Grease Interceptors with Appendix of Sizing and Installation Data

Underwriters Laboratories, Inc. 333 Pfingsten Road

Northbrook, IL 60062-2096

UL

Standard reference

number           Title

UL508-99       Industrial Control Equipment

Effective:                                                     01/01/2009

R.C. 119.032 review dates:                         07/01/2012

CERTIFIED ELECTRONICALLY

Certification

12/12/2008

Date

Promulgated Under:                           119.03

Statutory Authority:                           3781.10(A)

Rule Amplifies:                                  3781.10, 3781.11, 3791.04

Prior Effective Dates:                         3/1/98, 4/1/99, 12/1/00, 1/1/02, 1/1/04, 3/1/05, 9/6/05,

3/1/06, 7/1/07, 1/1/08, 3/31/08(Emer.), 6/24/08